Search results

hey all pine here, my kart is klipper kart with 6.5 predator motor and i put real cheap clutch to get it goin. im 6ft 4 and 220 but fit on it good, but clutch started heatin up after few minutes. i need some help buyin right clutch (heavier duty) also has fairly small tires. any sugest, thanx

hey all pine here, hey i been welding alot with my mig (lincoln) and i been using same wire that came with it basicaly for everything. (no alum) and i had to tack a piece of st steel the other day and it did work. inside welder it say must use stainless wire. now is that just so it dont rust...

built my 2nd kart, turned out pretty wild. i posted while back about cutting frame in 4 spots and lenghting a foot. well its done. i cut in 4 places(2 on each side so week spots if any would be scattered. i added 11 inches with of same diameter pipe with 5-6 in solid,(curb pin type)inside each...

hey all, any advice on hookin up a headlight or 2 to my kart with 212 pred motor and what i would need.? i have some small halegen driving lights and fog lights. thanx pine

i am wanting to make skis (snowmobile style) , trying to think of some materials i have laying around. probly metal but how long and wide. planning on 1in x 1in keel type runner on underside. my back tires grab good with my *** on it but front tires just plow snow. im pretty handy but looking...

hey all, I have piture of my kart but it don't show up like everyone elses when I post, any help, something to do with my log in-avatar etc. thanx pine

hey all, my 2nd cart progect has slowed down lately, 1 inch axle with new sprocket and hub. cant see any obvious damage to axle but get tiny bit of sprocket wobble when I turn it by hand. not like its loose wobble more like sprocket is bent. I don't think that's normal. also a lot of old paint...

the new 212 pred motor with 3/4 shaft --I slid new clutch on and it goes on to far. if I put 1-1/8 washer and bolt like it says clutch slides back and forth 1/4 inch. it says only use the set screws if motor shaft is not tapped. what do ya s think? thanx pine

what is largest size tires I can put on my kart? 212cc pred motor with cintr. clutch, cart made for adult fun. my other has 22x11x8 but has t.c. thanx

think im addicted now! my first build-restore turned out exelant, now I picked up another one yesterday and need some sugestions. all stock klipper cart with new 212 on the way. im going to cut rear top frame to be able to put taller tires and going to add a foot in length. seen one done where...

got er done (probly never actually be done) took first ride sat. need to get it to turn sharper, probly cause big rear tires and posi. also any way to put reverse in it? 212 pred motor--comet tc--posi any suggestions on either topic helpful thanx pine

brand new pred engine has on off switch, I am mounting new kill button on steering colum but not sure about wiring at motor. do I leave switch on motor also? im getting there, thanx again pine

hey all, back again, I was going to use my old tc from the old briggs motor to install on new pred 212cc. kart sat for 2yrs outside but tc is complete and looks to be in good shape, is there any kind of service I can do to it ? all parts look good--as for the driven part with the big blue spring...

hey all, just got my new motor 212cc pred. does anyone no bolt size for the 3/4 shaft that my tc goes on ? my old bolt from briggs seems alittle loose and old. 2nd ? is how to hook up throttle cable to new motor. came with silver throttle lever but need to hook up cable, thanx in advance pine

hey all pine here, I just got a kart, couple things say klipperkart. I need to replace motor but not sure what to get. will be used by adults and child. from what I read it has tc rather than clutch, everything seems to be there except belt. anthing to check tc out and motor is briggs with no...

morning all pine here, im in s jersey area with a few toys-trucks mostly- just had kart given to me but need some help id ing it, it has klipperkart pedals and engine plate same. motor is briggs but no good,no pull start so I cant tell hp etc. from reading a little looks like tc rather than...