New here need help

Status
Not open for further replies.

JBkartman

New member
Messages
29
Reaction score
0
It should I emailed them. So all I would need is a 3/4 jackshaft and a sprocket. How does the driven torque converter stay on the jackshaft without moving.
 

mysteryboy28

New member
Messages
1,582
Reaction score
11
Location
Lansing, MI
locking collars keep things in place on jackshafts and axles. if i'm trying to save a few bux and i know the sprocket or axle won't likely be changed or moved - i'll just tack weld (so you can grind it off later if needed) pieces of slightly larger tubing (perfectly fitting) onto the shafts/axles instead of using locking collars.

the jackshaft is keyed, and so is the driven pulley, so you wedge a 3/16" square key in-between the two to make them spin together.
 

Attachments

  • locking collar.jpg
    locking collar.jpg
    19 KB · Views: 1
  • locking collar 2.jpg
    locking collar 2.jpg
    47.8 KB · Views: 1
  • keys.jpg
    keys.jpg
    6.9 KB · Views: 1

JBkartman

New member
Messages
29
Reaction score
0
is this supposed to be like this? Are you suppose to just put the screw on to hold in place like this?
 

Attachments

  • IMAG1155.jpg
    IMAG1155.jpg
    63.1 KB · Views: 10
  • IMAG1154.jpg
    IMAG1154.jpg
    62.1 KB · Views: 12
  • IMAG1153.jpg
    IMAG1153.jpg
    86.4 KB · Views: 11
Messages
139
Reaction score
1
Location
Rochester, MN
Hey! The pictures you posted are EXACTLY what I recently had to figure out!

The clones my bro and I bought for our twin Karts have the same "shoulder" on the 1" engine shaft and we bought the same Torque Converters that you are using.

Here's what we did: took a Dremel Tool and put a grinding-stone bit on the mandrel... then we ground down about a 1/2 inch of the key-stock (that comes already inside the TC bore) that butts up close to the engine shaft-shoulder so that the Torque Converter hub could butt-up right against the shaft-hub....

then we purchased a longer fine-threaded bolt and an "extra thick fender washer" (Ace Hardware) (along with a smaller regular washer) then... we used an impact-wrench (because we couldn't hold the shaft from turning) AND some red-grade thread-lock compound and impacted the bolt and washers onto the front of the TC.

In the end: I wish the TC driver would slide about 1/4" closer to the engine... but then again... there is plenty of clearance between the driver and the engine housing in case of it flexing. Also: the belt itself now rides exactly over the engine shaft, so the empty space between the front of the TC and the engine shaft isn't compromised by the belt.

We're crossing our fingers that it works!!!
Good Luck!!!
 

JBkartman

New member
Messages
29
Reaction score
0
Thanks for the tips. Another questions do I order the 203443A item number torque converter belt for these dimensions? If im measuring correctly.
 

Attachments

  • IMAG1158.jpg
    IMAG1158.jpg
    70.8 KB · Views: 4
  • IMAG1159.jpg
    IMAG1159.jpg
    58.2 KB · Views: 6
Messages
139
Reaction score
1
Location
Rochester, MN
Ok... if indeed that is a 40 series Driver and Driven that you have purchased from gokartsupply.com, then you'll want a 7/8" Top Width Belt.

The call-number you wrote in the previous post isn't on that list of belts.

You need to somehow calculate the distance between the CENTER of the Engine Shaft and the center of your jack-shaft... so, if you engine has a 1" shaft, and you're putting your tape measure all the way accross it, then you'll have to subtract 1/2" (to measure from center to center).

I just held the tape measure right up to the front of the shaft, to the middle-threaded-hole and then to the center of my jack-shaft (in my case, my forward, N, Reverse transmission shaft). However you do it... you need to look at that belt chart, and establish a center-to-center distance that they sell a belt for.

It looks like you have somewhere around an 8" center-to-center distance... and there is NO belt for that distance. They DO sell a belt for 8 5/8" center-to-center distanc (203786A) On our GoKarts, we had to use the 11" center-to-center belt, because our transmission would have gotten too hot next to the engine AND our Driven pulley would have hit the side of the engine if it was any closer. I would suggest putting your Driven pully on the Jackshaft and see how much room you have to work with, and establish your center-to-center distance.
 

Regul8R

New member
Messages
14
Reaction score
0
Location
Houston, Texas
Here are a few pictures of my kart as we previously discussed. As far as the bolt size, I believe i used an inch and a half, just use a tape measure stuck into your gap space, whatever your gap space add about half an inch (or enough for good threading into shaft end plus bolt head length).
I had also wanted to pull the bolt and show you the gap space but i just haven't had time.
Plus a picture of a duck. Enjoy.
 

Attachments

  • 1017111846.jpg
    1017111846.jpg
    87.1 KB · Views: 10
  • 0504121841.jpg
    0504121841.jpg
    81.9 KB · Views: 10
  • 0504121840a.jpg
    0504121840a.jpg
    76.3 KB · Views: 8
  • 0504121840.jpg
    0504121840.jpg
    69 KB · Views: 9
  • 0504121839.jpg
    0504121839.jpg
    70 KB · Views: 9

JBkartman

New member
Messages
29
Reaction score
0
Thanks everyone and for the duck! got the driver set up just waiting on the sprocket and longer jackshaft I ordered.do you know how you set up your throttle?
 

Regul8R

New member
Messages
14
Reaction score
0
Location
Houston, Texas
I think "Peep" - the Duck - (as a duckling) was about 3 bucks at the feed store. Peep fun fact: He loved pecans. He flew south once it turned cold this past winter.

Now as far as the throttle cable it was very easy to hook up as the 420 comes with all the clamps / mounts for a throttle cable. The big clamp will keep your cable housing in place, then the little clamp on the throttle piece will clamp the metal cord in place.

Here are a few pictures. I took these and worked on them at 3:30am - pre-coffee. So sorry for poor quality.
 

Attachments

  • Pic0.jpg
    Pic0.jpg
    84.1 KB · Views: 10
  • Pic0.5.jpg
    Pic0.5.jpg
    84.5 KB · Views: 10
  • Pic1.jpg
    Pic1.jpg
    74.8 KB · Views: 8
  • Pic2.jpg
    Pic2.jpg
    86.8 KB · Views: 9
  • Pic3.jpg
    Pic3.jpg
    71.3 KB · Views: 8
  • Pic4.jpg
    Pic4.jpg
    72.9 KB · Views: 10

JBkartman

New member
Messages
29
Reaction score
0
Thanks on the setup. Does it matter which way the torque converter driven is put on . weather the spring is facing inward or out?
 
Status
Not open for further replies.
Top