Is this Briggs any Good?

Status
Not open for further replies.

Kentucky Boy

Member
Messages
611
Reaction score
49
Location
Bowling Green, KY
Bought an old go kart with this 5hp Briggs flattie on it. Had no compression. Upon opening it up I saw it had thrown the rod. Everything else looks good. The base of the cylinder has a small gouge in it. Is this block any good? Does the piston go down that far during the stroke?
 

Attachments

  • IMG_2887.jpg
    IMG_2887.jpg
    217.9 KB · Views: 22

Kentucky Boy

Member
Messages
611
Reaction score
49
Location
Bowling Green, KY
The governor had been disabled externally but the parts remained inside. The governor arm was left free swinging. I can't tell if the governor failed first or the rod. The crank is gouged some by rod wear.

And here is what's left of the governor and the rod. Luckily it didn't punch through the block.

Carnage. I have another crank and rod for this already just sitting around. The piston is still good. Cam and valvetrain are still good, and I already have most of the gaskets.
 

Attachments

  • IMG_2883.jpg
    IMG_2883.jpg
    275.8 KB · Views: 19
  • IMG_2882.jpg
    IMG_2882.jpg
    383.1 KB · Views: 31
  • IMG_2888.jpg
    IMG_2888.jpg
    434.9 KB · Views: 16
Last edited by a moderator:

Kentucky Boy

Member
Messages
611
Reaction score
49
Location
Bowling Green, KY
Been cleaning this old block up. It was nasty. The cooling fins on the cylinder were packed with dirt and grease. Still need to work on it some more. This motor has old points on it.

The inside is cleaning up nicely. Luckily no bad damage was done.

All the parts are laid out ready for a cleaning.
 

Attachments

  • IMG_2915.jpg
    IMG_2915.jpg
    312.4 KB · Views: 22
  • IMG_2913.jpg
    IMG_2913.jpg
    304.6 KB · Views: 10
  • IMG_2916.jpg
    IMG_2916.jpg
    426.8 KB · Views: 15
Last edited by a moderator:

Kentucky Boy

Member
Messages
611
Reaction score
49
Location
Bowling Green, KY
It appears to be removable somehow. The seal area looks to be lappable. I've never worked on one with points. The model type code is 130202 001501 18111507. What year is this motor? Probably needs a new exhaust valve and seat.

The points look ok. Just a little dirty.
 

Attachments

  • IMG_2894.jpg
    IMG_2894.jpg
    322.9 KB · Views: 19
  • IMG_2896.jpg
    IMG_2896.jpg
    328.1 KB · Views: 17
Last edited by a moderator:

Kentucky Boy

Member
Messages
611
Reaction score
49
Location
Bowling Green, KY
It is 78111507. The numbers have paint built up in them. Nov 15, 1978.

Making good progress on this motor. Cleaning it up real nice. Can't decide if I should paint it or leave it bare metal.
 

Attachments

  • IMG_2972.jpg
    IMG_2972.jpg
    328.1 KB · Views: 18
Last edited by a moderator:

Kentucky Boy

Member
Messages
611
Reaction score
49
Location
Bowling Green, KY
So I've noticed my springs are different heights. Guess I need new springs. This motor needs a new piston, rings, valves, springs, exhaust valve seat, rod, crank, head gasket, side over gasket, a carb rebuild and an air filter. I could probably buy two or three predators for the price of rebuilding this Briggs. At least the gas tank is rust free.
Edit: The springs are supposed to be different sizes.
 

Attachments

  • IMG_2999.jpg
    IMG_2999.jpg
    161.7 KB · Views: 5

Nosandwich

The REAL Poboy
Messages
873
Reaction score
22
Location
WHITE SETTLEMENT
So I've noticed my springs are different heights. Guess I need new springs. This motor needs a new piston, rings, valves, springs, exhaust valve seat, rod, crank, head gasket, side over gasket, a carb rebuild and an air filter. I could probably buy two or three predators for the price of rebuilding this Briggs. At least the gas tank is rust free.

Ummmm...its a 5hp Briggs. Go to a local scrapyard and pick up a mower. They might even have a tiller (even better) and use the parts off it.

Or go to OfferUp and look for something with a 5hp Briggs.

If you PM me an address, I can send you a crank for shipping cost only.
 

Kentucky Boy

Member
Messages
611
Reaction score
49
Location
Bowling Green, KY
I'll be rolling through BG in July. I'll put a 5hp Briggs (1992) on the curb.

Ha ha thanks. I'll have to get a second job if I get any more.

In anticipation of a successful rebuild, I bought some Briggs decals. I know they're not 1978 emblems but they're cool and I think they'll look good on this piece.
 

Attachments

  • IMG_3006.jpg
    IMG_3006.jpg
    370.7 KB · Views: 10
Last edited by a moderator:

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
In anticipation of a successful rebuild, I bought some Briggs decals. I know they're not 1978 emblems but they're cool and I think they'll look good on this piece.

You need this sticker so it is street legal.
Funny how it says Item 69730, which is a non-hemi predator 212cc. LOL
 

Attachments

  • sticker.jpg
    sticker.jpg
    16.3 KB · Views: 2

Kentucky Boy

Member
Messages
611
Reaction score
49
Location
Bowling Green, KY
Trying to decide what to do with the cylinder. I've read not to hone aluminum cylinders. I need a new piston and rings but don't know what size to get. Would it be ok with stock size or should I get an oversized one? Should I have it bored? Hone it and get a new stock sized piston and rings??
 

Whitetrashrocker

Inmate #952016
Messages
5,235
Reaction score
4,731
Location
Southern New Mexico
Get some feeler calipers and check the bore. If it's not round or has a big taper or hourglass shape, then you might not be able to save it.

You will need to measure it before ordering a piston and rings anyway.
 

Kentucky Boy

Member
Messages
611
Reaction score
49
Location
Bowling Green, KY
I may just put this one back together with a new rod, original piston and rings and see how it runs. I'm planning on just flipping the kart it came on to sell anyway.

Been putting this motor back together. Cleaned all the parts. Installed the new rod, new crank. Polished the piston a little and reused the rings. Here is my zip tie valve spring compressor. Works like a charm.

Lapped the valves and had to file some off the intake valve stem to get my lash correct. Almost ready for some paint.

Wound up putting a new exhaust valve in. While grinding to adjust valve lash I accidentally took off too much causing it to be too short. Got the new valve lapped in then set the lash correctly.

Put the new rod in. New main seals and a new side cover gasket. Tapped and plugged the governor hole.

Getting it all back together now. Painted the motor with high temp aluminum. Reinstalled the points and gapped them to 0.020. Gonna lap the flywheel and put it back on. I've painted it also.

Removed all the grease and paint from the gas tank and repainted it.

We'll see how it holds up.

The weather was perfect for painting yesterday. I was even able to get the starter cover stripped down, sanded and painted. Came out near perfect.

Closeup.
 

Attachments

  • IMG_2861.JPG
    IMG_2861.JPG
    148 KB · Views: 16
  • IMG_3318.jpg
    IMG_3318.jpg
    205.2 KB · Views: 11
  • IMG_3319.jpg
    IMG_3319.jpg
    307.7 KB · Views: 17
  • IMG_3354.jpg
    IMG_3354.jpg
    331 KB · Views: 15
  • IMG_3352.jpg
    IMG_3352.jpg
    270 KB · Views: 13
  • IMG_3361.jpg
    IMG_3361.jpg
    282.7 KB · Views: 12
  • IMG_3379.jpg
    IMG_3379.jpg
    277.7 KB · Views: 8
  • IMG_3380.jpg
    IMG_3380.jpg
    275 KB · Views: 9
  • IMG_3388.jpg
    IMG_3388.jpg
    271.6 KB · Views: 7
  • IMG_3400.jpg
    IMG_3400.jpg
    66.5 KB · Views: 8
Last edited by a moderator:
Status
Not open for further replies.
Top