hydraulic brakes questions

[gsegovia]

Where can I find some good and affordable hydraulic brake setup. Thanks

 

[alexisbomb1234]

you need more of a description, like what size axle, how fast does your kart go, whats yours budget. if your budget is around 100-200$and supposing you have a 1¼ inch axle, a great kit is http://www.ebay.com/itm/MCP-Hydraul...pt=Race_Car_Parts&hash=item3378c2f999&vxp=mtr this should be great.

 

[Swabbster]

go on ebay and pick up a atv brake setup, you can get them for around 50 bucks http://www.youtube.com/watch?v=149AxnAMMrQ

 

[OzFab]

go on ebay and pick up a atv brake setup, you can get them for around 50 bucks

ATV or motorbike, then simply fab up a few brackets

 

[Doc Sprocket]

Pitbike juice kits can be had pretty cheap on EvilBay. An alternate option is a wrecking yard. Depends on your skills and available tools.

 

[gsegovia]

you need more of a description, like what size axle, how fast does your kart go, whats yours budget. if your budget is around 100-200$and supposing you have a 1¼ inch axle, a great kit is http://www.ebay.com/itm/MCP-Hydraul...pt=Race_Car_Parts&hash=item3378c2f999&vxp=mtr this should be great.

I did have a detail description at first,but my phone crashed on me when I went to submit it. I was looking to keep it under a 100$, I got a one inch axle, plan on using 18 or 20 inch tires, 11hp engine with torque converter. Thanks

 

[gsegovia]

go on ebay and pick up a atv brake setup, you can get them for around 50 bucks http://www.youtube.com/watch?v=149AxnAMMrQ

I actually came across this, I sent there seller a question to see what size rotors work on that caliper. Thanks

 

[gsegovia]

Pitbike juice kits can be had pretty cheap on EvilBay. An alternate option is a wrecking yard. Depends on your skills and available tools.

Tools and skills is not a problem other then welding, looking to buy a welding machine for Christmas. Thanks

 

[Doc Sprocket]

I'm nearly certain that anything you buy will require a bit of welding, if even a simple bracket.

 

[gsegovia]

I'm nearly certain that anything you buy will require a bit of welding, if even a simple bracket.

Lol.... I know no worry half my family welds I was the one that decided to go a different route.

 

[jfxwave]

@Swabbster

I think the fluid of the cylinder is not enough so I don't think it would work because if you have 2 calibers it would need twice the fluid that 1 needs so you would need a bigger cylinder to push more fluid. I don't know how much that cylinder holds so you might want to check and see how far you will have to push the pedal to close both calibers.

 

[gsegovia]

@Swabbster

I think the fluid of the cylinder is not enough so I don't think it would work because if you have 2 calibers it would need twice the fluid that 1 needs so you would need a bigger cylinder to push more fluid. I don't know how much that cylinder holds so you might want to check and see how far you will have to push the pedal to close both calibers.

You had me going for a bit there, your replying to the question on the video.a member posted that in here so I can see the brake setup, to reply to it you'll have to log into you tube. Thanks

 

[gsegovia]

This is what I ordered.
http://www.ebay.com/itm/370662581806?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2648

 

[OzFab]

Cancel it. You're gonna need more than that to stop 11hp. At least find something with a twin piston caliper

 

[gsegovia]

Ok, how about two of this, the go kart I have had the Rear setup for twin band brakes so I can use the bar for two of this kits ill still come out cheaper then paying 180 for one of those twin piston calipers. Will that work

 

[Swabbster]

that kit is fine, that caliper is a 2 piston, one on each side, there very strong calipers, most 200cc atvs run about 10hp and they stop fine,

 

[gsegovia]

that kit is fine, that caliper is a 2 piston, one on each side, there very strong calipers, most 200cc atvs run about 10hp and they stop fine,

Well my plan is to test it out and see how it works out, if two are need then ill go for the next one. Thanks

 

[Doc Sprocket]

Well my plan is to test it out and see how it works out, if two are need then ill go for the next one. Thanks

Good plan- I actually do think there's a good chance it will be sufficient.

 

[OzFab]

that kit is fine, that caliper is a 2 piston, one on each side,

I didn't see that

 

[gsegovia]

am looking for a hub for this brake rotor it is, the bolt circle is about 2 1/4 inch, and the center hole is just under 1 1/2 any idea where i can find one, maybe some tips on how to make one thank you.