Clutch pre-engaging...

Status
Not open for further replies.

tribelwarrior

New member
Messages
24
Reaction score
0
OK so I'm new to go-karts and just bought my first one yesterday and already am running into issues. First off its a Wisconsin Robin 5hp w1-185. My problem is my clutch is engaging on the lowest possible idle setting and takes off slowly and the clutch starts smoking after a few minutes... I've already take the clutch apart and cleaned and inspected the weights of lubricant and oiled the bushing but no luck. My clutch has 10 teeth and my axle sprocket has 54 teeth if that helps. I also have 18 inch rear tires. Hope you can help me with my problem and thanks in advance for any assistance you can offer.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Your problem is your gearing is waaay too high. You're at 5.4:1 with those big tires. You need to regear to around 7:1 or 8:1, OR switch to MUCH smaller tires. This is NOT a clutch issue.

There IS a good chance that your clutch is now fried, but do NOT just replace it and keep driving. The new one WILL fail quickly as well.
 

tribelwarrior

New member
Messages
24
Reaction score
0
I'm a retard when it comes to go-karts so could you explain to me in baby terms how having more teeth on the sprocket will keep my clutch from engaging while the throttle is at the lowest setting... sorry If I'm looking like an idiot right now.
 

souperman000

New member
Messages
2,466
Reaction score
11
Location
Westlake Village, CA
I know you said this already...but is the idle control screw backed out way far? at idle the clutch shouldnt engage.

The gearing is important. You have a setup that allows a very fast top speed but not any torque for acceleration. What is happening is that the clutch is spinning and spinning and spinning tying to get a grip to move the kart. That causes friction and hence smoke. This is where gearing comes in to play. I never get the numbers right so wait for someone elseto tell you about it.
 

tribelwarrior

New member
Messages
24
Reaction score
0
I've back the screw out till just before the engine will shut off. I'm just not understanding how the sprocket affects the clutch pre-engaging because even if I took the chain off the clutch would still be engaging at the lowest idle setting. Like I said, I'm probably just making myself look stupid here but that's how we learn isn't it?
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
I bet you, 10 to 1, that the the chain is probably way too tight. This sounds to me like the chain is pulling down in the clutch, making the boots rub against the drum. You should have slack in yours chain, not too much though.
 

tribelwarrior

New member
Messages
24
Reaction score
0
When I pull on the chain in between the axle and the shaft there is about an inch of difference in position between pulling it out and pushing it toward the frame. If it is much more loose it will fall off.
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
okay then, is the engine revving high? No right? the clutch isn't getting burnt up, so tire size and gear ratios are out of the question. Now, lets get to the basics, this clutch is pre-engaging. Something has to be making the clutch engage, and by the sounds of it, the idle is set really low, so, lets get some questions answered. What type of clutch is this? What is the brand name?
 

devino246

Official DIYGK Chem Nerd
Messages
3,856
Reaction score
17
Location
Lynchburg, VA
okay then, is the engine revving high? No right? the clutch isn't getting burnt up, so tire size and gear ratios are out of the question. Now, lets get to the basics, this clutch is pre-engaging. Something has to be making the clutch engage, and by the sounds of it, the idle is set really low, so, lets get some questions answered. What type of clutch is this? What is the brand name?

Read his first post:

OK so I'm new to go-karts and just bought my first one yesterday and already am running into issues. First off its a Wisconsin Robin 5hp w1-185. My problem is my clutch is engaging on the lowest possible idle setting and takes off slowly and the clutch starts smoking after a few minutes... I've already take the clutch apart and cleaned and inspected the weights of lubricant and oiled the bushing but no luck. My clutch has 10 teeth and my axle sprocket has 54 teeth if that helps. I also have 18 inch rear tires. Hope you can help me with my problem and thanks in advance for any assistance you can offer.



If he's smoked his clutch, he's probably overheated the springs and ruined them which means that his clutch will now engage too soon. His problem is gearing. Gear down.
 

tribelwarrior

New member
Messages
24
Reaction score
0
In reply to devino; I've only ran it once on the new clutch and as soon as it got hot enough to smoke I killed it which was less than 3 minutes so I doubt the clutch is ruined from a couple minutes of being hot.
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
If it is gearing, the first things that will get burnt up should be the boots, at least thats always what happens to me. If the boots are wore down, it wouldn't engage like this. But, if it is the spring, which there is a chance it could be, then that might be it.

But, I would also like to ask this, if you raise the rear of the kart, and spin the axle, does the clutch grab?
 

devino246

Official DIYGK Chem Nerd
Messages
3,856
Reaction score
17
Location
Lynchburg, VA
If it is gearing, the first things that will get burnt up should be the boots, at least thats always what happens to me. If the boots are wore down, it wouldn't engage like this. But, if it is the spring, which there is a chance it could be, then that might be it.

But, I would also like to ask this, if you raise the rear of the kart, and spin the axle, does the clutch grab?

Either way, he's geared too high. 5.4:1 is too high with 18 inch tires.
 

tribelwarrior

New member
Messages
24
Reaction score
0
I didn't have to spin the axle, It was already spinning. But please don't say "That's because you overheated your clutch and ruined the springs so they engage too soon" because the wheels spun on idle before I ever heated the clutch up.
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
Hey buddy, loosen the bolt up just about a half spin, see if that helps a little. Now, it kinda sounds like you tightened the bolt into both the drum and boots, meaning, you tightened them both to the shaft.
 
Status
Not open for further replies.
Top