Bronda engine

Status
Not open for further replies.

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Well, I caved in last week and purchased another baja heat mini bike. Looks like this one is the oldest of the bunch that I have. Tires don't hold air, but show no signs of dry rot. I'll have to bust out the dish soap and water for this.

My goal is to have my three mini bikes up and running by Christmas for the kids.

1) this pictured one painted red/black. Bronda engine, genuine comet 30 series, tank and fenders painted digital camo red. Will have a small battery (not charged by engine) for front headlight and small led tail light. Gas tank I already have (since I removed the briggs tank). Tank is used on the 50cc mini bikes/scooters and will be mounted below the fake tank. Will let the bike look good while still being functional.

2) my old baja heat, painted military/olive green. Yellow or red star on each side of the gas tank. Not sure about fenders other than just painted olive green. (Ideas?) will have working headlight and tail light. Engine will be the JF 200 honda clone with a GTC 30 series torque converter. Small battery.

3) third bike is the baja warrior. It's almost in new condition. The problem is that the fenders and fake gas tank are all plastic :-( so I don't know if I want to waste any effort on them. Will be going to someone that has favorite colors of purple, and neons like orange, green. I'm thinking I'll just do some vinyl decals of racing stripes on the fenders, and maybe a skull or other decal on the tank. Any advice for decals or paint on plastic? Will have a 6hp subaru electric start engine, comet 30 series torque converter. Headlight and tail light.

Any comments/suggestions are welcome. Thanks!
 

Attachments

  • image.jpg
    image.jpg
    94.7 KB · Views: 19

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
So what kind of clear coat is best for plastics, or will any clearcoat do? I'm worried about flexing and adhesion.
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Glad it worked out for you. I have been too busy overwhelming myself with additional projects to have time for my other projects that I don't have time for :-D
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
https://youtu.be/WbzmNt8ivEA

Still playing around with the throttle, but I was able to get a lot of progress on the linkage using tig filler rod. So far so good. Ill have to fab a stop for the max rotation of the lever to avoid stressing the throttle butterfly or tig filler rod.

I bit the bullet and am going "all out" not for 7K rpms, but maybe 6k comfortably.

So far i have found out that the block I have doesnt have bearings on the crankcase cover side, which will wallow out under un-govered rpms.... so i bought a new old stock cast iron sleeved, dual bearing crank flathead for $150 shipped on ebay.

Next, i bought arc billet rod, arc billet flywheel. I also have stock appearing springs (important to not get too heavy of springs or you rob low rpm HP), billet lifters, and a 94ss cam, and hardened retainers. Nothing too heavy for springs, but just right for low end torque and still being able to achieve higher RPMs.

The weak point is now the piston, but I do not think the flathead i am getting in the mail will come with one, so I may end up buying a raptor 3 piston and rings.

Finally glad to get out in the garage again!!
 

Attachments

  • IMG_5068.jpg
    IMG_5068.jpg
    278.8 KB · Views: 9
  • IMG_0934.jpg
    IMG_0934.jpg
    378.9 KB · Views: 9

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Briggs 5 hp flathead shaved eyebrows

Well, this is my first attempt at shaving the eyebrows on the briggs 5 hp flathead. I didn't go all out on it as you can tell. It was kind of a toss up between leaving the center hump, or going for a even slope across. What do you all think? I figure it would be less hassle to have extra that needs shaving, than taking too much out.

I used my dremel rotary tool with the extension on it and only three attachments

60 grit sanding drum
240 grit sanding drum
some sort of polishing attachment

It didn't turn out perfect, but i think I did alright :wai:

I'll be porting and polishing tonight as well.
 

Attachments

  • briggs 5 hp flathead shaved eyebrows.JPG
    briggs 5 hp flathead shaved eyebrows.JPG
    128.7 KB · Views: 10
  • how to shave eyebrows on briggs flathead engine.jpg
    how to shave eyebrows on briggs flathead engine.jpg
    365.5 KB · Views: 7
  • IMG_5131.jpg
    IMG_5131.jpg
    287.2 KB · Views: 7
  • IMG_5130.jpg
    IMG_5130.jpg
    309 KB · Views: 9

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Porting and Polishing Briggs 5 hp flathead

Here are a few before and after pictures of porting and polishing.



I took the pointy sanding bits, and they loaded with aluminum so they suck, then i thought oh hey i have all these wood bits i hardly ever use. GOLDEN!!! these things are awesome. I mostly used the rounded nose one with a taper to it, then finished up with some 100 grit sanding of sharp edges. I did not increase the intake or exhaust diameter, only roughed up the intake a little, and smoothed out the exhaust a little and then polished the exhaust. Very minor port job, and I am ok with how it turned out.

I have heard that if you take some more off of the intake and exhaust that will help with flow at higher RPMS, but I figure that the carb I have now is the most restrictive part on the whole thing, so I will not worry too much about porting any more.
 

Attachments

  • IMG_0954.jpg
    IMG_0954.jpg
    203.4 KB · Views: 9
  • IMG_0946.jpg
    IMG_0946.jpg
    303.2 KB · Views: 10
  • IMG_0947.jpg
    IMG_0947.jpg
    205.7 KB · Views: 8
  • IMG_0948.jpg
    IMG_0948.jpg
    209.8 KB · Views: 8
  • IMG_0957.jpg
    IMG_0957.jpg
    228.9 KB · Views: 10
  • IMG_0956.jpg
    IMG_0956.jpg
    240.6 KB · Views: 10
  • IMG_0952.jpg
    IMG_0952.jpg
    355.7 KB · Views: 10

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Briggs 5 hp Performance Parts

Well i got a few performance parts for the briggs engine. Still waiting on copper headgasket and a possible spring mix up. For those that may want to get briggs 5 hp performance parts, google is your friend and you can probably get all of these in one store, but.... here is where I got mine just as an example

flywheel/connecting rod - ombwarehouse
stock appearing springs, hardened retainers, 94ss cam, billet stock length lifters -checkered flag racing
.042 and .030 copper head gasket - robert's kart shop
RLV muffler for 1" OD header- ebay
'vintage' briggs flywheel cover sticker - ebay


places that sell all of this stuff also include turk brothers, comet kart, and out2win racing, you can get the arc stuff and dyno cams stuff from the manufacturers website, but its cheaper to get from one of their dealers.

One thing I still need to do, but am debating is to reinforce the lifter galley (since this is not a raptor engine) so it wont fatigue over time. Problem is, I cant weld aluminum with my TIG welder, and my mig welder will do it but its $255 for the spool gun bleh. Anyway, here is a pic of the stuff.
 

Attachments

  • briggs 5 hp performance parts.jpg
    briggs 5 hp performance parts.jpg
    484 KB · Views: 7

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Briggs 5 hp performance upgrades

Well, I have been busy emptying my pockets, and have finally gotten the engine started. I was debating putting in a raptor III piston, and I am glad I did so the engine will be reliable at 7000 rpm. I doubt I will hit that as the carb is the most restrictive point on the engine now. The porting I did, was just to knock down the casting flaws so that can be improved on, as well as decking the block, but I will not do that at this point.

One pull on choke and it died, second pull with choke off and it fired right up. Yay! Good ol honda carbs (or knockoff in my case).

For those of you that know briggs. I used a newer cup style recoil on the old school crank... This means that I actually cut the crank off at the thread for the nut. I dont reccomend doing this, but there was no way I was ever going to use the old school pull start. I remember messing with them as a kid, traumatized for life. I had to space out the flywheel cover by 3/8" as the original block had a different side cover.

For break in, I set the RPMs to 2500 from idle and ocasionally varied from 1600-2500, mostly keeping at 2500 with a light load (torque converter on it with belt, no chain). Turned it off after 10 mins of run-time and will repeat this 2x, then will empty break in oil, inspect, add the other half of the quart bottle of break in, then lightly ride around for a while.... next week... when I don't have work *sigh*

Here is what's in it:
.027" copper headgasket (stock is .050")
94SS cam (mild cheater cam)
billet stock length lifters
new/aftermarket 'stens' valves,lapped, and lash set to .005" intake and .006" exhaust
springs recommended by checkered flag racing for the cam and other parts
honda clone carb, with custom made intake/exhaust/throttle
header is .87" ID (25mm OD sanitary stainless)
muffler (yet to be put on) RLV 1" ID
hardened retainers
arc billet connecting rod, stock length, clearance within spec
arc billet flywheel, non adjustable, lapped, timing set to 30 deg btdc (cam recommends 30-32) magneto gap set to .030"
spark plug indexed (open side faces exhaust), gapped at .030"
Raptor III standard size piston and rings, with raptor wrist pin
 

Attachments

  • IMG_0973.jpg
    IMG_0973.jpg
    220 KB · Views: 7
  • IMG_0966.jpg
    IMG_0966.jpg
    303.1 KB · Views: 7
  • IMG_0967.jpg
    IMG_0967.jpg
    312.2 KB · Views: 7
  • IMG_0964.jpg
    IMG_0964.jpg
    250.2 KB · Views: 8
  • IMG_0979.jpg
    IMG_0979.jpg
    260 KB · Views: 8
  • IMG_0982.jpg
    IMG_0982.jpg
    357.4 KB · Views: 8
  • IMG_0977.jpg
    IMG_0977.jpg
    253.4 KB · Views: 7
  • IMG_0976.jpg
    IMG_0976.jpg
    322 KB · Views: 7
  • IMG_0975.jpg
    IMG_0975.jpg
    363.5 KB · Views: 6

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Bronda almost finished

Broke the engine in. Mini bike mostly finished. Pops wheelies from stop on full throttle. Idle set to 1650 rpm.

Revs up to about 3800-4000 rpm before it starts shifting. I took it to 4100 rpm on a straight away before I ran out of room. Put on custom stainless exhaust. 1" I'd RLV muffler added and I noticed a nice increase in torque but it only revs to 3800 on that same straight away.

I am thinking that the gx200 carb is just too restrictive and am weighing my options. Don't get me wrong. The bike runs like s champ, but I need to take advantage of all those performance mods.

22 mikuni carb ok?
What about these tillotson carbs?
Also. I will be porting a little more and may end up shaving off a little more towards bore for the eyebrows.
 

Attachments

  • image.jpg
    image.jpg
    427.4 KB · Views: 6
Status
Not open for further replies.
Top