Edwin Spangler
Well-known member
- Messages
- 1,084
- Reaction score
- 1,082
Having a big truck is cool and all but how do you account for the torque inaccuracy?
ST2-NG Pre-build "Think Tank"
- Thread starter Kartorbust
- Start date
Kartorbust
Inmate #627
There's a formula to adjust to a lower setting or you put the torque wrench 90⁰ to the adapter and the amount does not change. If the amount is 180ft/lbs, you drop it to 155ft/lbs and you'll achieve the torque spec. Since the cylinders get torque to either 15ft/lbs (I think have to look it up again) or 13ft/lbs, long as I have room, should be fine.
-1200x965.jpg?sfvrsn=b7003621_1)
www.terex.com
How to Adjust Torque Values When Using Torque Adapters
Understanding fastener torque and the corresponding values is important when working on Terex bucket trucks and Terex digger derricks.
Kartorbust
Inmate #627
Cylinder hone showed up yesterday. Any recommendations for a honing oil? Evidently the company I got the hone from, also has like a 1 gallon jug of their own oil for sale on Amazon. Thing is, I may need like maybe a quart to a half gallon tops to do both cylinders.
Hellion
Murderator
- Messages
- 9,254
- Reaction score
- 4,223
Buy it, unless it’s redickerously expensive. Buy it anyway. Otherwise, seen people using any oil even WD.
Denny
Canned Monster
When I worked for Buick I would use ATF in a squirter oil can. You don’t need to soak it just keep it wet. Soak the stones for a half a day or so before you use the hone.
Kartorbust
Inmate #627
Okay its smaller than I thought. Guess its a pint, but never clicked on it until now. But they do offer a 5 gallon bucket.
Hellion
Murderator
- Messages
- 9,254
- Reaction score
- 4,223
Soaking the stones is next level brainery. Nice one, Denny. Same for the ball hones as well or are those not recommended? I was trying to think of ATF (it’s like the perfect consistency too).
Denny
Canned Monster
Same with the dingle ball hones, used to soak those too. When done with them I’d put them back into the ATF and soak them to clean the stones.
Kartorbust
Inmate #627
I got the dingle ball style hone anyway. Those tend to give better results.
Master Hack
Well-known member
Kerosine! A little ATF additive if ya want.
Use plenty to flush away the particles that are removed.
Use plenty to flush away the particles that are removed.
Kartorbust
Inmate #627
Surprisingly, unless I go to maybe Tractor Supply or possibly Wal-Mart, Kerosene is not very common out here. In Minnesota, Fleet Farm had at least 1 pump, maybe 2 where you could fill up a can with Kerosene. Out here in Nebraska, haven't seen anything.
Will keep it in mind though. I might have 1 bottle of Mercon LV sitting in the garage, not open.
Will keep it in mind though. I might have 1 bottle of Mercon LV sitting in the garage, not open.
Master Hack
Well-known member
Lamp oil is kerosine also, and you get a nice citronella scent. Here on the left coast even hardware stores carry it. #1 diesel is the same stuff purdy much.
Smoking while honing is not recommended.
Smoking while honing is not recommended.
Kartorbust
Inmate #627
Fortunately I don't partake in cancer stick smoking. But where's your sense of adventure?
Master Hack
Well-known member
Who said any thing about cigarettes?
Whitetrashrocker
Inmate #952016
We just put the cylinder in the solvent sink and let that run while we hone.