Torque Converter Problem

Status
Not open for further replies.

Nma__1

New member
Messages
7
Reaction score
0
Hi,
I currently have a go kart that i build my self and it has a couple issues. The main one being the clutch to axle system. I have a predator 212cc with a jet'd carb and an exaust, but the problem is that i burn through clutches within a week of good riding. The teeth of the clutch actually get sheered off, and im not sure why this is happening. Anyone have any ideas?

---------- Post added at 07:03 PM ---------- Previous post was at 07:02 PM ----------

I was thinking about getting a torque converter, but the space between my drive shaft and my axle is not enough to fit anything more than just a clutch.
 

Jrgunn5150

Rudderless
Messages
1,028
Reaction score
12
Are you certain that the clutch is aligned, and more importantly, the correct chain size is being used?
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Premature sprocket wear:

1) wear on one side of sprocket is a sign of misalignment
2) saw like teeth, where sprocket teeth valleys get deeper is a sign on chain that is too tight
3) rounded ridges is a sign of the chain becoming too lose, usually happens if chain slips and skips over the teeth ridges

Also like jrgunn pointed out. Chain size is a big deal.

Take your chain and look at it, can you move it freely or does it get kinks in it? Are the rollers round or do they have flat spots in them? Any Knicks/burrs?

Proper chain tension is also important. You don't want it too tight or too lose.

Also, based on what you have said about the engine and clutch, you may just be putting out more HP than the clutch can handle.

Here are a few questions:
1) tooth count on clutch
2) tooth count on axle sprocket
3) tire diameter

Ideally for stop and go driving a standard yard kart should be geared for about 25 mph at 3600 rpm.

Another thing. The torque converter can be pointed straight up. It looks weird, but that orientation does work with limited space.
 

Nma__1

New member
Messages
7
Reaction score
0
1. 12 teeth
2. 60 teeth
3. 18 inches

I was unsure about how to mount the torque converter with limited space, but that gives me a good idea.
Also i have made sure to use the correct chain size 35

---------- Post added at 10:14 PM ---------- Previous post was at 10:07 PM ----------

how would i mount the torque converter vertically?
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
Wow. that ratio and tires is NO good for a clutch.
Typically we see and recomend
12
72
and no more than 15.

You can run 18s but you need different gears.
Like 80 and 10.
Or a torque conv. or Jackshaft
 

Denny

Canned Monster
Messages
12,066
Reaction score
8,605
Location
Mayberry, Indiana
I'm confused do you have a centrifugal clutch or a tav system because from what I'm reading everyone is talking about both.

Denny
 

Nma__1

New member
Messages
7
Reaction score
0
Could someone give me a recommendation for a torque converter system for a go kart running with a predator 212cc. Also the space between the drive shaft of the engine and the sprocket on the axle is small so how would i install it?
 

ezcome-ezgo

G'me sumthin to write on
Messages
6,032
Reaction score
3,045
Location
Atlanta, GA
Repeating what others have said, if you could post a picture or 2 it would be very helpful.
Look on eBay for torque converter kits with a 3/4" bore. There are plenty to choose from.
 

leesiel

Yardcart 196
Messages
223
Reaction score
1
Location
Savannah G.A.
[/QUOTE]
Another thing. The torque converter can be pointed straight up. It looks weird, but that orientation does work with limited space.[/QUOTE]

So would a t.c. be adaptable (easily,somewhat) to a dead axle?
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Another thing. The torque converter can be pointed straight up. It looks weird, but that orientation does work with limited space.[/QUOTE]

So would a t.c. be adaptable (easily,somewhat) to a dead axle?[/QUOTE]

First off; why not just regear???? (Even with a TC...you may need to anyway! )

Second: WHERE ARE THE PICS?

Third: Why do you think you need 2 threads for 1 question?
 

Nma__1

New member
Messages
7
Reaction score
0
1. What do you mean by re-gear?
2. I dont have a camera available to me although i will soon

3. I asked two different questions, so i thought i would make a different thread, i was under the impression that different questions go on different threads.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
He means that the rear axle might need to be potentially a 72 tooth sprocket instead of 60..... hence the word re-gear.
 

Denny

Canned Monster
Messages
12,066
Reaction score
8,605
Location
Mayberry, Indiana
1. What do you mean by re-gear?
2. I dont have a camera available to me although i will soon

3. I asked two different questions, so i thought i would make a different thread, i was under the impression that different questions go on different threads.

Not if the questions are about the same cart and related :thumbsup:

Denny
 

FreeRunner15

=======
Messages
660
Reaction score
10
Location
================
So would a t.c. be adaptable (easily,somewhat) to a dead axle?

When i made the clutch to TAV conversion on my dead axle kart the sprockets wouldn't line up at all ...

..so i redesigned my kart.

You could drill an area where you want the engine to be mounted a bit more on the left side of the engine mount.
 
Status
Not open for further replies.
Top