where is the QUALITY??

Status
Not open for further replies.

slideways

New member
Messages
575
Reaction score
6
Many flatties were aluminum bore. Only the I/C versions and the Raptor were cast iron. So where's the quality there? ALL clones are cast iron bore and dual ball bearing crank.

Can you not gain hp with a clone by adding a header/filter/jet? I'd have to say that thousands of clone kart racers out there think they are worth it. A clone with the very simplest racing mods are DESTROYING fully blueprinted Briggs Flatties every week on the racetrack. They have to put a restrictor plate on the clone or move the stock clones up to run with the high dollar flatties running restricted to even compare them.

Just because its been around for years and still runs doesn't make it a better engineered design than something i can buy new today and take care of and get more power out of cheaper than a flathead.
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
the chinese exel at cheap products mass produced

slowly they are clicking they can mass produce good products and it is still cheap

sound familiar
remember the 80s and 90s
remember "jap crap"

this was cheap mass produced products out of japan
they worked out that they can mass product good products
honda blows briggs out of the water today

what are the main stream bike brands
honda, kawasaki, suzuki and yamaha

what are some top electronics companys
panasonic, sony, teac, apple (america owns it but doesnt built it)

cars
europe still has the flashest fastest cars
but again
toyota, mazda, honda, mitsubishi and nissan all compete or exede ameriacan and australian cars

i challenge u all to walk around your own homes and just look at the productsu use every day

i know americans are quite patriotic and will never admit somone eles is better, aussies are the same
but it is the basic fact our companys may have the skills, but unlike the 70s or 80 when americans brought american and aussies brought australian they cant compete against the asians

EDIT
also i agree with sideways
we have all honda motors
our grain augers sit in the weather all year round
we have 10 year old augers that have never had the carbs cleaned
the spark plugs were so old the nut had rusted off
but the augers alway start and run strong
i serviced them last year purly because i was bored

and unlike briggs we have brand new honda fire fighting pumps and the qualityis the same as the older ones

even my 80s 250cc buggy
the poor thing is so beat up the seals are non existant
and the salt air has got into everything so it takes 10 minutes to start
but when it gets going it runs like new
 

B man

Tecumseh FTW!
Messages
2,490
Reaction score
3
Location
Oliver springs,Tn
any engines a good engine as long as its well taken care of. and i like clones because there not as bad as people say. mimic something indestructible(Honda) and you get something Very tough.(clone) and briggs and Kohler. Weren't they the same company for a while?(for some reason i think they where?) Tecumsehs IMO are the best.
 

B.M.800

TheBeal.
Messages
2,387
Reaction score
26
Location
Central PA
Briggs have been sh!t for decades, just about everyone else has always been leagues ahead, both in terms of quality and design.

By far, the worst quality engine I have ever worked on was a 3.5hp Briggs with a late 90's build date. I've worked on tons of Chinese stuff but nothing compares. I'd rather they made the tin work out of plastic (like Honda GCs) than that stupidly thin tin that tears with the first decent yank (and you needed many decent yanks) on the pull starter.....

I wonder if maybe you guys arnt getting the same "quality" Briggs engines we get... I dont know were B&S biggest buyers may be, bit its possible they would be getting better quality than somewhere that doesnt see that many briggs...

Know what I mean? Just a thought. I havnt had much experience with briggs, aside from 3.5hp pushmowers. They seemed to always run fine. The 5hp briggs I have now has some starting issues... but I havnt messed with it much...

europe still has the flashest fastest cars
I disagree. I think they look ugly... maybe if it had a few dents here an there. make it look more rugged. :D
 

sexyvicta

New member
Messages
806
Reaction score
2
plastic cams are sweet and cast iron bores are kind of pointless now as most engines never get used enough before they are replaced + when they are worn out its cheaper to just buy another than pay a guy to rebuild it. Briggs does offer the cast iron bore on its comercial engines which cost more $ anyway.

i've never had any serious issues with briggs engines they just sound like crap. tecumseh sounds nicer.

as for honda blowing briggs out of the water...they cost twice the price...
 

slideways

New member
Messages
575
Reaction score
6
Maybe this guy just abused his crap. I have a 6.75 series motor. Its 6.75ft lbs..NOT hp. On a pressure washer that runs fine. Its a flathead and has never had the oil changed in 2 years of washing racecars.

They dont use hp rating anymore because of all the lawsuits. So you'll see 8.75 on some Briggs motors and alot more cc measurement advertising.
 
Status
Not open for further replies.
Top