whats is its purpose

Status
Not open for further replies.

jamyers

Well-known member
Messages
1,444
Reaction score
49
Location
Buffalo Gap, TX
Yes, same as removing a mechanical/centrifugal governor, except yours is all outside the crankcase. Same cautions apply, of course.
 

ML-TOYS

New member
Messages
2,908
Reaction score
21
Location
long island, new york
Thanks guys, i was always under the assumption that the governor was internal. Just learned something new.
This seems like a much easier gov removal and no remaining parts to self distruct in the crankcase.
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
I have a question: My daughters kart has this setup, vane connected to one side of the throttle butterfly & accelerator linkage to the other side. So, with your foot firmly planted on the accelerator, how does the governor do it's job?
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
So, with your foot firmly planted on the accelerator, how does the governor do it's job?
Your accelerator is working through the gov linkage, just as if it were setup for a tiller, generator, lawnmower, etc.
No matter how hard you step on pedal, rpm will not exceed set rpm (~3600).
By-passing gov is quite easy. Directly connect accelerator linkage to butterfly. This will override anything the gov wants to do. Springs associated are exceedingly weak.
 

ML-TOYS

New member
Messages
2,908
Reaction score
21
Location
long island, new york
Thanks for the replies EVERYONE,

Russ you said disconnect it, should the flapper part be removed or can it just be fixed in a permanent position. If fixed in place which position is better for air flow purposes ?
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
Russ you said disconnect it
I didn't say that.
Disconnect is not necessary.
I would just leave it where it is. Air flow will not be affected regardless of position of air vane.
As previously stated, cable can be directly connected to butterfly and will overpower gov with NO ill effect.
 

ML-TOYS

New member
Messages
2,908
Reaction score
21
Location
long island, new york
I didn't say that.
Disconnect is not necessary.
I would just leave it where it is. Air flow will not be affected regardless of position of air vane.
As previously stated, cable can be directly connected to butterfly and will overpower gov with NO ill effect.

Sorry just woke up when i read that post :oops:
Thanks again
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Your accelerator is working through the gov linkage, just as if it were setup for a tiller, generator, lawnmower, etc.
No matter how hard you step on pedal, rpm will not exceed set rpm (~3600).
By-passing gov is quite easy. Directly connect accelerator linkage to butterfly. This will override anything the gov wants to do. Springs associated are exceedingly weak.

Sorry but, no, my accelerator is hooked directly to the throttle butterfly linkage. Does this setup render the governor useless?
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Ok, to be technical, it's connected to the butterfly control plate. Here's a pic of the linkage setup but, unfortunately, it doesn't show the connection to the butterfly. That being said, the governor linkage is connected to the same point
 

Attachments

  • SDC10100.jpg
    SDC10100.jpg
    87.7 KB · Views: 9

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Accelerator linkage & governor linkage are both connectet to the other side. connecting there would pull the butterfly closed.

I'll stop hijacking for now, I'll PM later
 
Status
Not open for further replies.
Top