What Model West Bend Is This?

Status
Not open for further replies.

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
IDK.. only think I could think of is measure the displacement.
a 820 has slightly over 2.5" in bore and 1.6something inches of stroke,
(8.2 cui -134cc)
So in case you see a 134 stamped on the cylinder - crank case it's likely an 820.

There must be easier ways I guess.. the thing is, I don't know.. I'd wish I'd have an 820 to tell for sure ;)
mayby dimensions? the 820 is 6.6" from center of PTO to the top of the cylinder head, 1.75 from PTO center to the bottom of the case
the cylinderhead is almost 5" wide (4.9 or so)
I'd say the 580 is a hair smaller than that but I can't tell ...


'sid

PS great purchase!
 

gokarttimmy

Member
Messages
167
Reaction score
14
Location
Pittsburgh,Pa.
Thanks-I will take measurements upon delivery. I'm also assuming that a serial number or something is on it somewhere. It's gonna need a fuel tank and some paint and new decals. My Simplex is not 100 percent original-but it's close enough to have been invited to several vintage Kart events. So it needed a Clinton Panther or West Bend 2 cycle to be period-authentic.....I saw this one on Ebay and grabbed it before anyone else did. And I think I got it for a reasonable price. Well under 300 bucks-and it runs.....
 

gokarttimmy

Member
Messages
167
Reaction score
14
Location
Pittsburgh,Pa.
West Bend Serial Numbers

I have a West Bend 2 cycle and discovered the number plate on the bottom of the fan shroud. It is a Chrysler Pentastar plate with the numbers "58041" and "1210". Please excuse this if this is a dumb question-but am I to assume it is a 580? Can anyone explain the West Bend numbering system? Thanks to any info.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
please stick with one thread!

*merged*

[EDIT]

58041 is a Chrysler Power Bee 4hp engine.
(a WB 580 hence the serial.. just not the full 6.5hp the 580 west bend power bee produces in the kart config)
unfortunately I cannot tell you waht difference there is between the 4hp and the 6.5hp versions *shrugs*

'sid
 

gokarttimmy

Member
Messages
167
Reaction score
14
Location
Pittsburgh,Pa.
What carb do these models use? It runs good, but may need a decent cleaning/rebuild. How do I figure out which carb? It is a Tillotson of some sort.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
tillotson pumps are also on numerous other carbs with inbuild pumps...

IF it is a Tillotson carb it'll be a HL series.. size is dependend on your venturi (measure it ;))
exact modelnumber should be stamped onto the carb body..
looks like it's a HL299 but I can't tell for sure

a good overall maintenance guide can be found here:
http://www.lazair.com/HL.htm

'sid
 

gokarttimmy

Member
Messages
167
Reaction score
14
Location
Pittsburgh,Pa.
Thanks-I am a newbie with 2 cycles-but my Simplex was sold with either a WB or a Clinton Panther and I want it to be historically accurate. The one I have is a great runner-starts up with about 3 pulls when cold-but I don't know how long it's been since the Tillotson was serviced. I would like to rebuild it eventually.....
 
Status
Not open for further replies.
Top