vertical shaft conversion with horizontal cylinder?

Status
Not open for further replies.

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
I've seen several photos of vertical shaft engines converted to horizontal shaft, and in all cases the cylinder points upward. Is there any reason why I shouldn't orient the cylinder horizontally?
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
because of the oil. you will need an oil slinger for it to be upright in most cases. if the engine is tipped then the oil may pour out either the exhaust or the intake. ever tipped a lawnmower sideways, and then your air filter is soaked in oil? but, if you push the handle down and tip the cyl straight up it has no problem, exept its not getting oil.
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
When your filter gets soaked it's because the oil has traveled through the breather tube in the valve cover. What if you put the valve cover on top?
 

slideways

New member
Messages
575
Reaction score
6
What about when you shut the motor off and the crankcase full of oil leaks past the rings and through the open valve... into your carb or exhaust and out?
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
I can't think of any reason why it wouldn't work, but I just thought I'd throw the question out there in case I was overlooking something. Seems like it wouldn't be a big deal, because in its normal configuration the cylinder is sideways...

It's a Briggs 8 hp, and the current plan is to put it on a mini bike. I thought it would be nice to have the flexibility to place the engine in different positions.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
nice, i just got a 8hp briggs. headbolts :mad2: :mad2: :mad2: :mad2: :mad2: :mad2: :mad2: :mad2: :mad2: :mad2: :mad2: :mad2: :mad2: :mad2: :mad2:

it would be hard to come up with a mount on its side though.
 

slideways

New member
Messages
575
Reaction score
6
Did you not even read my post regarding how are you going to keep oil in the engine?
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
When I converted my lawn mower engine to horizontal shaft it was much easier to have it upright for a few reasons. First off you would have to make a new inlet manifold with a 90 degree bend in it instead of using the original one and just turning the carby. If you've seen the ridiculous inlet set up that Briggs mower engines have, you will understand how bloody difficult that would be.

You can't make it lean towards the cam side because all the oil will leak out the breather and you wouldn't be able to get the dipper anywhere near the oil because the dipper would hit the cam, my dipper comes REALLY close to the cam an it's pointing down, not to the side. You can't make lean to the other side because the crank and big end would always hit the oil so you'd loose power if you don't kill your engine first. I doubt the valves would get much oil in that set up either.

You could probably lean it a bit each way, perhaps if you were going to lean it to the cam side you could make a blanking plate for where the breather goes and drill and tap the other side or the block and place a one way valve in it. there's still the problem of getting moving the oil though. The slinger is driven off the cam so you could probably just rely on that.

I hope that all made sense.

Thanks

Hayden
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
I guess the thing to do is take it apart. It's been a while since I actually looked inside one of these. It should be fairly obvious how to get the oil to work right once I have it opened up.

As long as I have to build a new intake pipe anyway, I'm thinking of using a brand new Honda carburetor rather than the old Briggs carb. We had several of these old 8 hp Briggs engines back in the 70s and 80s when I was a kid, and the carburetors always had a little bit too much "personality".
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
I guess the thing to do is take it apart. It's been a while since I actually looked inside one of these. It should be fairly obvious how to get the oil to work right once I have it opened up.

As long as I have to build a new intake pipe anyway, I'm thinking of using a brand new Honda carburetor rather than the old Briggs carb. We had several of these old 8 hp Briggs engines back in the 70s and 80s when I was a kid, and the carburetors always had a little bit too much "personality".

Seeing as yours is an 8HP it'l be the next block size up from mine so it will most likely be quite different, mine was just a 10cu" 4hp.

I made up a whole bunch of dummy dippers out of tin from old cans, you should really do the same before you make your final dipper. I'm certainly glad I did, saved me a lot of time.

My dipper was simply a piece of 2mm thick steel that I cut and bent into shape.

And yes, the good old Briggs 8HP carb can be a bit "fun".:roflol: I'd get a motorbike carby instead of a Honda one though.

Good luck with you project mate! :thumbsup:

Thanks

Hayden
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
Is it a common problem for the oil to leak past the rings in a normal vertical shaft engine?

Nope, the oil level isn't high enough for the it to reach the piston/bore. The "MAX" oil level is usually about 5mm below the edge of the bore. So oil can't leak past the rings unless you store your mower on an angle.

Thanks

Hayden
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
Oh and one more thing, it will try and rip your arm off when you start it, they back fire on start up because there isn't the inertia of the blades to keep it turning. Make sure your pull starter is up to the challenge, mines broken 2 pull starters and snapped the rope on another one.

Mines a b!tch to start and it's got half the HP of yours. I'm now making a kick starter for mine, it's that bad.

Thanks

Hayden
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
My engine is equipped for electric start. The only thing missing is the electric starter, but I have 3 dead engines with starters on them. That will make it a lot easier....
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
How about this idea: If I want to mount the engine horizontal, I'll just make sure it's angled up at least a few degrees to keep the oil out of the cylinder. This is all subject to the final design of the bike, which I want to build out of old Honda 3 wheeler pieces, including front and rear suspension and fat 22 inch ATV tires. If it fits best in a vertical position, then it will be vertical.

Regarding the motorcycle carburetor, which one do you recommend?
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
Well the bolt pattern has to be the same, unless you cut 2 manifolds and weld them together.

What size motor is this again and brand?
 
Status
Not open for further replies.
Top