Two Carb issues o.O

Status
Not open for further replies.

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
Honda GX390 Clone Generator This one went through 2 carb cleanings, the usual lemon juice bath for 20 mins, being blasted with carb cleaner, etc. The Jet, Emulsion Tube and passages are clean for sure. It will start up in a few pulls, and then it will surge. I have adjusted the gov. screw and used my Tiny tac to keep it around 3600, but it runs rough. In the video of it below, you need to turn your volume up loud to hear the way it surges. I'm not really sure what can be causing it since the carb is clean and fuel is flowing. If anyone can give me some pointers, that'd be great. I'm thinking something in the carb is still dirty since it sat for a loooong time with gas in it, but I can't seem to find it. As mentioned, the jet is clean as can be.
http://s1247.photobucket.com/albums...on=view&current=video-2012-06-15-20-17-12.mp4

Briggs Lawn Mower Carb
This one is an issue with the carb on a lawnmower. I cleaned it with my mentioned steps above and put it back together. Once connected to the tank, gas will flow from one of the holes on the choke side of the carb. In the picture, I pointed with the pink wire. The needle is seating and I know that b/c I can blow air in to the fuel intake and when I push up on the float, the needle plugs in to the rubber seal. All the parts have been changed with a rebuild kit.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Generator- Sounds like it's bouncing off the governor. I've seen engines do this with no ill effect. I think it's caused by a slight governor misadjustment or sloppy linkage or weak spring. The effect tends to occur with no load. As a test, run it with a significant load and see if it smooths out. Plug some high-load electrical devices in, and see what she does.

Lawnmower- The fact that you can FORCE the needle to seat means nothing. Normally, it's only a wee bit of pressure from the float that seats the needle. I think one of three things is going on. Either the needle is not quite seating properly (with that wee bit of pressure from the float), the float is not adjusted correctly, or is defective and not floating.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
Okay. The generator was still surging even with my fridge plugged in to it. The voltage meter bounces back and forth and the fridge was varying in power. I'm going to boil it again just to make sure, then I'm going to change all the gaskets which seemed to be in good shape. If that fails, I'll mess with the governor spring some more. The arm is slightly bent out of being 100% straight, but it looks good enough to me. The generator was made in 2005 and it sat for a while, I can tell. But it runs fine with the only exception being the fluctuating RPM. It's also difficult to start it. As I write this, it seems more and more clear that the carb is still dirty.

Finally, there is a fuel mix screw which I have turned 1 1/2 turns counter clockwise. Though the screw is a small needle in the carb tube, how does this play too much role in surging?

As for the lawn mower, I'm going to remove the needle plug, and reinsert it more gently. Perhaps I pushed it too far in to the fuel passage.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
I made new gaskets with legitimate paper (no cereal boxes used) and thought that might work since the other ones had to be scraped off with a blade, but it only started with carb fluid, then ran for about 30 seconds. it ran erratically probably because the governor screw was a bit out of whack. Finally, the pull rope broke since I replaced it with some nylon string. What is the best type of rope to use for a 390? I see it takes a lot of force to turn over an engine connected to an alternator. I'd rather not pay as much as the repair shop down the street will charge me, but if I can't find anything over the weekend, I'll get some from them on Monday.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
The mower is fixed. If anyone has this problem where fuel won't stop leaking, it's 90% of a chance that the needle is not seating properly. To fix this, I hooked the old rubber plug and carefully reinserted it by pushing a small screw on top of it, displacing the force among the whole plug. Don't insert it too hard, or the needle won't plug the engine hole.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
So... Something like this?

Lawnmower- The fact that you can FORCE the needle to seat means nothing. Normally, it's only a wee bit of pressure from the float that seats the needle. I think one of three things is going on. Either the needle is not quite seating properly (with that wee bit of pressure from the float), the float is not adjusted correctly, or is defective and not floating.

LOL- Glad you got it sorted out!
 
Status
Not open for further replies.
Top