Turboing a 212cc predator

Status
Not open for further replies.

jd8430

jd8430
Messages
8
Reaction score
0
Location
Alabama
Hey guys I'm new on here and I need sum help turboing my 212cc predator. I have a upgraded air filter and jets and I have a free turbo. I just need some advice.
 

jd8430

jd8430
Messages
8
Reaction score
0
Location
Alabama
Mainly I need help oiling it. I don't know too much about it. I do know that they have to have 20 psi of oil. I need to know where to get parts. I've some of the threads and they have helped a little. I don't have any internal mods? Do I need to mod my motor? I do not have my governor out.
 

Flyinhillbilly

The great cornholio
Messages
2,468
Reaction score
132
Location
North West Arkansas
I actually signed up here because I was thinking about turboing a predator. I've turbocharged several V8's and even a motorcycle, but decided that a predator was just more hassle than it's worth due to the lack of a pressurized oiling system or charging system. That pretty much just leaves you the option of a belt driven pump which equals $$$. Then there's the fuel system. If your turbo doesn't have a carbon seal on the compressor side then you'll have no choice but to go with a blowthrough carb or EFI, either of which will require a fuel pump and boost referenced fuel system.
I'm not trying to be a downer, but it's going to be a lot of work and money to boost a $100 engine that probably won't live too long under boost anyway, and believe me brother, I have no issue with blowing up $100 Chinese engines. I'd be glad to help any way that I can, but I want to make sure that you understand what you're getting in to with this.
 

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
Mainly I need help oiling it. I don't know too much about it. I do know that they have to have 20 psi of oil. I need to know where to get parts. I've some of the threads and they have helped a little. I don't have any internal mods? Do I need to mod my motor? I do not have my governor out.
I forget the company name, believe it's EcoTrons or close to it, sell a Chinese clone of the IH mini turbo and they sell an oil pump and cooler for it. It does draw a good chunk of power so you'll want a stator or a really good battery.
 

jd8430

jd8430
Messages
8
Reaction score
0
Location
Alabama
I'm intruiged with turbos and one of my buddies had one he sed hes give. I'm not sure where my other reply went but I need help oiling it mainly and any other information. I don't no to much about it. Ive been reading on the internet but there isn't any place that says how they oil it or anything.

Any info will be appreciated

---------- Post added at 06:41 PM ---------- Previous post was at 06:37 PM ----------

I've been telling people I wasn't going to stop till I blew it up.
 

jd8430

jd8430
Messages
8
Reaction score
0
Location
Alabama
It comes off of a 1.8 liter motor

---------- Post added at 06:50 PM ---------- Previous post was at 06:50 PM ----------

I've said his 5 horse will spoil and run awesome
 

Flyinhillbilly

The great cornholio
Messages
2,468
Reaction score
132
Location
North West Arkansas
You'll never spool that. It's probably something close to a GT15. I had one of those on my 750 and it ripped, but I don't think a 212 even has the slightest chance of spooling it.
 

Attachments

  • image.jpg
    image.jpg
    352.4 KB · Views: 10

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
Not enough to justify the cost. One would be better off just doing a larger carb, air intake, and exhaust. It might add 1-2hp on a good day. Not worth it on this small of an engine. The time and effort to make the associated parts to make it work, as well as getting the carburetor to work properly without spewing fuel everywhere, to me isn't worth the cost or effort for small gains.
 

Flyinhillbilly

The great cornholio
Messages
2,468
Reaction score
132
Location
North West Arkansas
How many equestrian units do you think that'll add to the basic 6.5?

A general rule of thumb on turbocharged engines is that it will double the HP at 15psi. Since atmospheric pressure is ideally 14.7psi, when you double that pressure you should in theory double the amount of oxygen and fuel in the cylinder and therefore double the output. That doesn't account for the pumping losses of the turbo, but it's close. So a stock rota-derp at 15 psi should make 12-15 hp.
The torque curve is really what makes the difference. Since boost isn't rpm dependant, it will reach and maintain full boost as soon as the turbo spools and hold it through the maximum rpm, which makes insane amounts of torque at low rpm, but at the same time is also very prone to connecting rod failure due to the cylinder pressure that it makes.

Not enough to justify the cost. One would be better off just doing a larger carb, air intake, and exhaust. It might add 1-2hp on a good day. Not worth it on this small of an engine. The time and effort to make the associated parts to make it work, as well as getting the carburetor to work properly without spewing fuel everywhere, to me isn't worth the cost or effort for small gains.

I couldn't agree more, just build the engine. You can reach the limits of the block easily enough by just building it.
 

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
Even better, look no further than CarsandCameras attempt at turbocharging their drift trike and the nightmare that turned out to be. The amount of time they spent trying to turbo that 420 is just insane. They had to ditch the carb for a $700+ fuel injection kit, that I might argue gave them more power than that turbo was putting out. Speaking of that EFI kit, that was a nightmare for them to even install. Like I said, you're better off building up the engine than adding a turbo for better gains, or getting a larger engine all together. If it's going into a custom frame, you'll be many hours ahead with a larger engine than a turbo 212.

I think even a N20 (nitrous oxide) kit might be cheaper and would give similar gains as the turbo. But for $99.99 plus the turbo, oil cooler and pump, associated parts for all of that, you'll be at the cost or well above for a 420cc engine, or built 212, with larger gains.

If it's for wheelies out the wazoo, you can hear it deep to compensate so much cheaper. Point is, anyone looking to turbo an industrial engine, you'll save your self time, money and headache by going with a built or larger engine.
 

Bbqjoe

Banned
Messages
3,455
Reaction score
70
Location
Location, Location
If it's for wheelies out the wazoo...




Excuse me?
 

jd8430

jd8430
Messages
8
Reaction score
0
Location
Alabama
what would a 150cc dirt bike motor do on there? I couldn't even spool it making my exhaust pipe smaller for more pressure? How would a 150cc dirt bike motor perform? I can't complain about the way it runs stock but I'm one that likes the feel of power.
 
Status
Not open for further replies.
Top