Trying to work out the kinks

Status
Not open for further replies.

Everett45

New member
Messages
23
Reaction score
0
Location
Idaho
My go kart has an 8hp B&S with a torque converter. I took it out for a spin today. I started her up, and let it idle for a good minute. I so much as touch the throttle and it tries to die. Eventually after several more minutes it's a little more forgiving. I hop on, and take it down the road a ways. I turn around to come back, and all is well until I hit the uphill incline, which was very minimum. I began giving it more throttle, to no avail. It wouldn't rev up anymore, and it became somewhat unresponsive to throttle input. No matter the throttle, I barely made it up the incline. I haven't tuned the carb yet, but it seemed fine for the first bit. I tried turning IN the idle and full throttle mixture screws, because my friend suggested it might be running rich. I tried to start it up after that, to no avail, even after returning the screws to where they were. Another thing is that my throttle cable is attached to the governor arm, which in turn is attached via rod to the throttle valve on the carb. Is this interfering with the action of the governor? It seems like since I am pulling in the arm with the cable that it wouldn't be able to move back up and close the throttle. Any ideas? I'm quite lost right now.
 

Attachments

  • image.jpg
    image.jpg
    364.3 KB · Views: 6

PredatorPowaaa!!

Mistake Maker
Messages
103
Reaction score
0
Location
Ontario,Canada
Have you tried putting gas in it?
No jk, I would check the carb bowl for dirt and even if there is none, I would partly disassemble it and hit it with some carb cleaner. Maybe poke a sewing needle through the main jet to clear it. Oh and before all of that, check the air filter and possible carbon build up in the exhaust. And make sure your fuel lines aren't clogued. Could also be the clutch, but you said it was idling bad so I'm going to assume its engine related
 

Everett45

New member
Messages
23
Reaction score
0
Location
Idaho
I finished the build mid December, and it's sat indoors since then due to weather. The carb was clean and it seemed to function fine before. I'll have to clean it again to make sure. Fuel lines should be fine, and it's got a new air filter. The tank had maybe 1/3 or 1/4 left, I wonder if it needs more 'weight' to it to get better fuel delivery...? Also, by carbon in the exhaust do you mean on the valve or in the pipe? The same old muffler is still on it.
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
I have never personally had any issue with Fuel. But...
I have heard stories of gas getting old. Right we all have. But seriously
these new additives and crap they put in the gas I have heard Sometimes Gas will in fact
go bad and gumm up the carb. Within even just a month. At least dump the remaining gas and start with fresh gas.

I am not saying tear up your carb and rebuild it, just "don't rule it out" cause it could actually be the culprit.
 

pRoFiT

Can't buy it?, build it!
Messages
1,151
Reaction score
64
Location
California
ah man no. the kinks are known for lola!!

https://www.youtube.com/watch?v=LemG0cvc4oU

much better song from them.

---------- Post added at 01:13 AM ---------- Previous post was at 01:06 AM ----------

Is that return spring hitting the governor? Could be causing the engine to try and cut of power. Possibly? I don't know just throwing out ideas.
 

PredatorPowaaa!!

Mistake Maker
Messages
103
Reaction score
0
Location
Ontario,Canada
Lol I know my spelling isn't great, but hey if you can read it and know what I meant, then I doesn't really matter. Oh and by carbon build up, I mean in the muffler. Although, if it is an old engine it could be the valve. Since you said its an old miffler, I would take it off completely and take it for a short ride. And I mean short. Its not good to run an engine with no back pressure. If it works, buya new muffler or make your own pipe.
 
Status
Not open for further replies.
Top