Sprocket Questions (Newbie)

Status
Not open for further replies.

karlskartisthebest

New member
Messages
2
Reaction score
0
So, I bought an engine off of eBay. It's a powerland 16 horse. I know that's a lot of power but I'm a big guy.

Anyways, I have purchased the deluxe love axle plans from Kartfab and plan to build it. With some slight modifications. I am just so lost when it comes to picking the correct sprockets.

Id like to get a 40 series tourqe converter. Which I know will need a jack shaft, which will be no problem but the moment I get to calculating ratios and how many teeth a sprocket needs. I freeze.

Anyone have any suggestions or a guide somewhere online to help me make sense out of all of this.

Thanks so much.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
:welcome2: the forum.

All will become clear very soon, grasshopper.

We need to know approximately what your kart weighs with you on it....and how tall your rear tires are, and what kind of terrain you plan on using it on.
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
What he said and here is some info from last week:

To put it simply. and with 11" tires for these examples.
For example a 9:1 ratio would be 10 tooth clutch and a 90 tooth axle.
However this would be like driving a stick shift stuck in 1st gear. Smoky burnouts but no speed
and
a 3:1 ratio (10clutch and 30 Axle) would be the opposite. Stuck in 5th gear but burnt clutch from a dead stop. biut if you got a push start/down hill you get a hellacious top speed.

So we recommend 6:1 (10 and 60 or 12 and 72.) This is a good all around ratio.

If you did not already see from above. you figure the ratio by dividing the axle gear tooth count by the clutch tooth count. 72/12=6 therefore 6:1 ratio.

That is one of the reasons why on your other thread Somebody was saying, What is the point of High Hp engines.
You have a ton of HP and will get to top speed quickly but Karts are single speed so you are limited by RPM.

Also why I suggested 5:1 possibly 4.5:1

Normally 4.5:1 would NOT work, but the extra HP of your 670 and the high Quality Clutch it may work and get you more speed.

Thank you for posting this. Many folks seem to think that more HP means more speed. No, speed is determined by rpm. Higher hp gets you to maximum rpm more quickly (better acceleration) but rpm = rpm so a 6.5 hp Predator and a 24 hp honker running at the same rpm gives the kart the same speed.


---------- Post added at 10:19 AM ---------- Previous post was at 10:07 AM ----------

Also just found this from "GAB Nation"
Well a kart with an "inertia" clutch, or Centrifugal Clutch as they are more commonly referred to, that has a 5:1 gear ratio starts at 5:1. Like starting a car in highest gear.
The same kart with a 30 series TC starts at 13.5 : 1 so it gets moving easier. Starting a car in lowest gear.

So A TC allows faster gearing.

30 series have a 0.9 : 1 overdrive so when at full speed, the 5:1 is actually 4.5 : 1.

TC belts start to slip at high RPMs where good clutches generally will not. (I've only read this and no way could give you an RPM limit for your kart) Most racing karts use clutches. Some "OutLaw Yard Kart" racers use torque converters.

Hopefully someone else will chime in with more experience with CC's vs TCs.

Chinese TCs are fine, their belts tend to be inferior. Lots suggest getting a good belt ~$25, but my original Chinese belt has held up so far.
 

Joe-405

Enjoying New Projects
Messages
2,673
Reaction score
98
Location
U.S.A.
DO NOT use a 30 series on that engine ! Only a 40 and above. Especially with a kart.
 
Status
Not open for further replies.
Top