I may have finally found a clutch. what do you think?

Status
Not open for further replies.

TonyMontana214

New member
Messages
88
Reaction score
1
Location
Dallas
Ive been trying to find a clutch for my 24hp GX670 Honda and i think i finally found one. Seems too good to be true but i think this one may work. Now if this is the one how many teeth should my sprocket have so i can have the fastest speed. The forum does not let me upload the screenshot of the clutch but here is the link.

http://www.heeters.com/kartclutches.shtml

The clutch im looking at is the Enforcer Clutch.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
The machine/buggy/kart/vehicle for which it is to be powered?
Is that 11" OD or rim size of the tires? If OD.. Then a 12/72 combo will work good..
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
With the 24Hp and your want for max top speed you can get away with better than 6:1. On 11" tires I would say 5:1 easy! maybe even 4.5:1
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
To put it simply. and with 11" tires for these examples.
For example a 9:1 ratio would be 10 tooth clutch and a 90 tooth axle.
However this would be like driving a stick shift stuck in 1st gear. Smoky burnouts but no speed
and
a 3:1 ratio (10clutch and 30 Axle) would be the opposite. Stuck in 5th gear but burnt clutch from a dead stop. biut if you got a push start/down hill you get a hellacious top speed.

So we recommend 6:1 (10 and 60 or 12 and 72.) This is a good all around ratio.

In your case with the 24hp and expensive clutch I suggested you could do 5:1.

If you did not already see from above. you figure the ratio by dividing the axle gear tooth count by the clutch tooth count. 72/12=6 therefore 6:1 ratio.

It looks like the clutch you want is available in different tooth counts. See if it is possible to buy just a different "gear only" then you have choices and can try different gear ratios.
buy swapping a 12 dollar gear as opposed to buying another 100 dollar entire clutch.
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
Sometimes especially on higher quality Clutches the 10 or 12 or... tooth Gear on the clutch itself is changable.
So you can buy the whole clutch with a 12 tooth and also but a 10 and 14 tooth "gear only"
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
On the link you posted look at the Racing cent.clutch.
under replacement parts it shows
several different gear and bushings for 16.99.

I do not see that option on the enforcer.
but it is worth asking the seller
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
I think with the enforcer clutches, have the drum and sprocket machined as a unit.. That's why they list different clutches..
 

TonyMontana214

New member
Messages
88
Reaction score
1
Location
Dallas
Ima give that a try in couple of weeks. I might buy some springs that allow it to activate at a lower rpm

---------- Post added at 09:39 PM ---------- Previous post was at 09:30 PM ----------

I was looking at a speed calculator. It said that with 12/72 i would get maybe at 30 mph which i think is a little too low.
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
I was looking at a speed calculator. It said that with 12/72 i would get maybe at 30 mph which i think is a little too low.

That is one of the reasons why on your other thread Somebody was saying, What is the point of High Hp engines.
You have a ton of HP and will get to top speed quickly but Karts are single speed so you are limited by RPM.

Also why I suggested 5:1 possibly 4.5:1

Normally 4.5:1 would NOT work, but the extra HP of your 670 and the high Quality Clutch it may work and get you more speed.
 

Iron John

New member
Messages
397
Reaction score
26
Location
NA
That is one of the reasons why on your other thread Somebody was saying, What is the point of High Hp engines.
You have a ton of HP and will get to top speed quickly but Karts are single speed so you are limited by RPM.

Also why I suggested 5:1 possibly 4.5:1

Normally 4.5:1 would NOT work, but the extra HP of your 670 and the high Quality Clutch it may work and get you more speed.

Thank you for posting this. Many folks seem to think that more HP means more speed. No, speed is determined by rpm. Higher hp gets you to maximum rpm more quickly (better acceleration) but rpm = rpm so a 6.5 hp Predator and a 24 hp honker running at the same rpm gives the kart the same speed.
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
That is kind of a High gear. Thats where it gets tricky. It might work, and it might not. Thats why it would be nice for you at this point in the build, to try to get some built in Adjustability in the Gearing options.
I mentioned some clutches you can get removable/replaceable Gears but also you can buy 2 piece Axle gears so they are easily swapped out with out totally disassembling the drivetrain.
 

TonyMontana214

New member
Messages
88
Reaction score
1
Location
Dallas
True. Ima give them a call about that. Also, would a clutch that activates at a lowrr rpm give me more speed since it has more rpm to rev up? Or would that just burn out the clutch faster.
 
Status
Not open for further replies.
Top