Somebody do the math

Status
Not open for further replies.

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,887
Location
Chicago-town USA

Attachments

  • Stage 1 212.jpg
    Stage 1 212.jpg
    178.8 KB · Views: 7

Jrgunn5150

Rudderless
Messages
1,028
Reaction score
12
Looks like HP peak is around 4800, so governing the thing is like hamstringing it.
 

Dukkie

New member
Messages
39
Reaction score
0
Location
New Braunfels TX
Easiest thing to do is get a 79 dollar Torque converter off ebay.

done.
and im equally dis satisfied by the results in the opposite spectrum.

now it has what torque i feel would be normal (or slightly under) but responsive enough one wouldn't complain. However top speed was reduced significantly.


i bought the 7" and it came with the wrong inner diameter chain sprocket, the sprocket also had a keyway already part of the sprocket, (which would have made the included key way rest to far out making the nut impossible to thread on, IF the sprocket even fit over the jackshaft anyway) the kit did not have a bolt long enough to hold the cvt to the engine shaft and did not have the large washer in between that same bolt and the cvt. the ebay seller was to interested in telling me how the picture is correct and it should work fine more than he was interested in fixing their mistake with correct matched parts.

so.. i bought a 6" ebay kit from a different seller, everything in it was fine so i installed but used the belt and driven from the 7" diameter kit, i wondered if maybe my experience in the post above was because i over purchased on the diameter so i swapped out the 7" installed the 6" diameter and i liked it even less so i put the 7" back on.


With the 7" installed it will easily get up to a normal sunday driving cruising speed but that's all it has. on the street i don't believe the motor is ever getting up to full rpm that is has available while on jack stands.
on the street the torque converter driver doesn't look like its compressing more than half way (is this based on rpm) so its not using all the gear ratio it should be. (causing top end to flat line at cruise speed?) on jack stands i believe it compresses with the belt almost to the full outter diameter of the driver? (motor side) and full inner diameter of the driven? (jascksaft side)

now im looking for help.

i should try to get a video of this so it can explain better than i type.
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,887
Location
Chicago-town USA
When in overdrive,

The Belt should run on the outer edge on the DriveR unit.

Seems like it may not be up shifting when under load.

I was able to get to 42 mph on my buggy with 16" tires, TC, and 6:1 gear ratio.
4800 RPM.
Maybe you need the 8T for the TC?
The up shifting of the TC????
Not my best area of knowledge

---------- Post added at 10:53 AM ---------- Previous post was at 10:51 AM ----------

I know this would generally mean less top speed.
But would it make the TC up shift correctly???
Fellas???
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,887
Location
Chicago-town USA
I would check and make sure both the driveR and driveN are installed correctly. Make sure the driven spring has the right preload.
Play around with which hole the driveN Spring in loaded into.
Make sure chain and sprockets are aligned.

????
Those are my best guesses, which are sometimes not very good.
 

Dukkie

New member
Messages
39
Reaction score
0
Location
New Braunfels TX
I would check and make sure both the driveR and driveN are installed correctly. Make sure the driven spring has the right preload.
Play around with which hole the driveN Spring in loaded into.
Make sure chain and sprockets are aligned.

????
Those are my best guesses, which are sometimes not very good.

they are good guesses, i just now have to google what they mean.
upon inspection it does look like i may have a spacer on the wrong side as Driven / driver are correctly installed / positioned slightly off chain / sprocket are misaligned equally
no clue what preload is, i have heard spring color may mean something, but what i don't know. but the 7" i think is gray the 6" is red.
hole spring is loaded into i have no clue, that part was pre assembled.


Run on Jack Stand Video
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,887
Location
Chicago-town USA
it does look like i may have a spacer on the wrong side as Driven / driver are correctly installed / positioned slightly off chain / sprocket are misaligned equally.

Run on Jack Stand Video

In the video it looks the the belt goes crooked.
Make sure the pulleys are aligned. I can imagine that if the pulleys are not aligned perfectly (or close to) than the TC will not fully engage.

Maybe it is the camera angle, but it LOOKS TO ME like it needs aligning.
The sentance I quoted was less help than the video.:rolleyes:

---------- Post added at 12:29 PM ---------- Previous post was at 12:26 PM ----------

The DRIVEN unit has to come further out on the crankshaft (or so it looks to me).

Possibility of Athlete's foot on the third toe on left foot?
 
Status
Not open for further replies.
Top