Smoking belt

Status
Not open for further replies.

Rob711

New member
Messages
64
Reaction score
0
Location
Long Island, N.Y.
Hey this is my first real thread here so forgive me if I'm doing something wrong. Picked up a well used Yerf 3203. Worked fine for a lap around the flat neighborhood.
After it got to its new home about three hrs away (father in laws cabin) engine became hard to restart, then would run for about 30 sec and die, as if needle valve was blocked. Took it apart quick while still on engine, cleaned out jet and gas was freely flowing out needle valve. Back together now gas freely pours out air intake as well as primer bulb, this is 6.5 hp tech. Plan to remove carb, look it over on the bench and reassemble and install. If not harbor freight 212, seems like the route.
On to the belt, before using it I took off the comit 30 drive clutch cleaned it, reinstalled. Driving the cart up a hill with my self and daughter, about 240 lbs combined, it was struggling. Belt was smoking and now rubber bits/ dust all over engine. I figured belt was worn, so I will order a new one. Wife and daughter gave it a run, sounds like it's trying to start off in third gear, sounds like a lot of load, but hardly moving. Not much to this clutch as far as part go, springs seemed ok, that inner piece slides through nice after sone Emory cloth, brass bushing intact.
Could it have been from engine not getting full power due to carb issues, worn belt, or clutch problem?
Thanks
Rob
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
A little belt slip upon engagement is normal, but if the kart wont move, but engine revs up, then you have a belt and or gearing problem. What you can do (if you are going to ride up a bunch of hills and whatnot) is get an 8 tooth 5/8" bore 40/41/420p type C sprocket. This will change yoru gear ratio so you will lose a little top speed, but make the engagement of the torque converter easier on the belt as it doesn't have to slip as much before engagement.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
could also be the driven unit (worn buttons.. cam slipped and unloaded the spring)

would you mind post a pic of your TC pulleys (both driver and driven) just to be sure you don't ruin your new belt in a short amount of time (belts are not too cheap)

'sid
 

Rob711

New member
Messages
64
Reaction score
0
Location
Long Island, N.Y.
I will get some pics this eve, if I can figure out how to post them via my iPhone. I just stopped home and measured the width of the belt, it's .5"?!, I've read that it was .75 new, so that can't help. Yes I don't wanna eat up a new belt either, thanks.
I also read about those 1,2,3 marks on the clutch, should I set it to the number 3 spot, being its hilly where the majority of the riding will be? Any tutorial on that?
Rob
 

Rob711

New member
Messages
64
Reaction score
0
Location
Long Island, N.Y.
Ordered new belt, took apart carb, put it back together, no gas pouring out, too late to start. The chain looks like it comes in contact with the driven clutch at times, or really close. Can anyone see other problems, grabbing the jack shaft it seems ok. Have to measure the drum the brakes it's tough to stop currently.
I put a 212cc harbor freight on a 1968 ariens snow blower with great success, huge fan of those engines vs tech. But don't wanna scrap this engine if I don't have to. Will let u know
Rob
 

Whitetrashrocker

Inmate #952016
Messages
5,238
Reaction score
4,739
Location
Southern New Mexico
The inner surfaces of the tc where the belt rides needs to be removed of rust. A 3m brillo pad on an air tool made easy polishing.

You might find the inners are rusted up too.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
So no slipped cam that's good..

but indeed you should remove the rust from the pulleys sheaves...
they should be as smooth as possible rust only causes premature belt wear..
and we don't want that, do we?

'sid
 

Rob711

New member
Messages
64
Reaction score
0
Location
Long Island, N.Y.
Premature anything is usually bad! I'll clean them up. Would a wire wheel on angle grinder be too much. Only have air impact wrench.
Is the chain and clutch clearance something to be concerned about? Man buying this buggy I saw the bent spindle and suspected worn belt. Oh well buyer beware. Still a fun project, thanks for the input
Rob
Ps when it gets up I'll make it smoke till it pukes!
 

Attachments

  • image.jpg
    image.jpg
    300.1 KB · Views: 2

Rob711

New member
Messages
64
Reaction score
0
Location
Long Island, N.Y.
Thanks bob! So it runs! I'm assuming it was just a stuck float, idles on the high side, if I had a new belt I think it would be moving. I guess I'll start a build thread.
 
Status
Not open for further replies.
Top