please help with clutch

Status
Not open for further replies.

mkellam

New member
Messages
6
Reaction score
0
Ok so when yall talk about noobs without knowing it you are referring to me. Im 27 and have never even rode on a go-kart. That being said any answers need to be in plain english although I am mechanically knowledgeable. What I have is a go kart that I bought for my kids and want to finish fixing it. I have the full frame tires and a motor. what I do not have is the clutch. I thought that they were all the same until I went to buy one and found out different. I believe I have all of the info that someone would need to tell me what I need. The tires are AT22X11-8. They are 22 inches tall. The sprocket has 60 teeth and is 10 inches tall. I plan to put a 5 horse briggs and stratton that i already have that is bone stock. I also noticed while counting the teeth on the sprocket that I have to turn the tire twice before the sprocket will make one complete turn. This go kart will not be for competition I am not looking for the most speed just the power to climb hills and it will be for kids from 6 to 13 and as they get older. I hope that that is all the info that is needed if more is needed just let me know and I will correct it.
 

mkellam

New member
Messages
6
Reaction score
0
also if I am in the wrong forum and there is a better site to answer my question let me know so i can get it posted there
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
What you need is a jackshaft. The least number of teeth you can fit on a centrifugal clutch is 10t. With your setup that would be geared for 40mph.
You could also get a torque converter, but you would still be geared for 40, which is way too much for a 6 year old!
A centrifugal clutch would be smoked on a 5hp geared for 40.

With a jackshaft you could get a 12:1 ratio, and gear it for 20. Then as the kids get older you could change one of the sprockets on the jackshaft (around $10) and the kart would be faster.
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
What you need is a jackshaft. The least number of teeth you can fit on a centrifugal clutch is 10t. With your setup that would be geared for 40mph.
You could also get a torque converter, but you would still be geared for 40, which is way too much for a 6 year old!
A centrifugal clutch would be smoked on a 5hp geared for 40.

With a jackshaft you could get a 12:1 ratio, and gear it for 20. Then as the kids get older you could change one of the sprockets on the jackshaft (around $10) and the kart would be faster.

The jackshaft would be the easiest and best idea right now. With the 22" Tires and rear sprocket, he needs a gear reduction and by the sounds of it, he probably doesn't want to spend all of the money on a TC. Good thinking r_chez.
 

mkellam

New member
Messages
6
Reaction score
0
ok thanks for your help now one more question if i run this jack shaft than will i still need a centrifugal clutch? like i said im a little ignorant on the matter.
 

mkellam

New member
Messages
6
Reaction score
0
ok never mind that last question I answered my own question by doing a little research on the jack shafts on go karts. I will try to figure out the sprocket sizes that I will need if any one has experience in the matter than please let me know what you would use to get this thing down to a kids speed
 

mkellam

New member
Messages
6
Reaction score
0
Thanks to you all is what the last one was supposed to say before my phone made a mess of it
 
Status
Not open for further replies.
Top