piston and rod length

Status
Not open for further replies.

kevbo22

Member
Messages
347
Reaction score
0
Location
Colorado
why would you change the piston and rod length?
what kind of benefits does it have?
From what I understand id doesn't change displacement, only bore does, or am I wrong?
 

Jfive

New member
Messages
645
Reaction score
1
Location
Great falls Montana
Rod only changes the angle the stroke is changed by the throw of the crank. Different angle reduces side load of a piston, and it frees up a bit of power and affects the power curve.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Rod only changes the angle the stroke is changed by the throw of the crank. Different angle reduces side load of a piston, and it frees up a bit of power and affects the power curve.

Yes...but just barely...what different rod length and piston often does is move the assembly higher up in the bore..( increasing compression)....given the same length with the change ( longer rod...shorter piston....ending up the same overall length) it will indeed reduce side load and make the engine slightly more "tourqy" ....( taking less effort to redirect the piston under load.)
 

Jfive

New member
Messages
645
Reaction score
1
Location
Great falls Montana
Yes...but just barely...what different rod length and piston often does is move the assembly higher up in the bore..( increasing compression)....given the same length with the change ( longer rod...shorter piston....ending up the same overall length) it will indeed reduce side load and make the engine slightly more "tourqy" ....( taking less effort to redirect the piston under load.)
True if the piston moves up the cylinder. Could just buy a piston that increases the compression, don't need the rod to do it. I figure a longer rod is good as long as the piston pin doesn't interfere with the rings. I look forward to building up my long rod 400 Ford but with a long rod from the factory compared to other sbf engines it had the lowest compression of them. The cc of the engine ultimately decides the compression.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
True if the piston moves up the cylinder. Could just buy a piston that increases the compression, don't need the rod to do it. I figure a longer rod is good as long as the piston pin doesn't interfere with the rings. I look forward to building up my long rod 400 Ford but with a long rod from the factory compared to other sbf engines it had the lowest compression of them. The cc of the engine ultimately decides the compression.

Sort of....the swept volume vs the compressed volume does....( provided you have good rings and seated valves...lol).

But as you said...IF you move the piston closer to the head ....you will increase compression....reguardless....(but relative to original compression and the only change).

You could actually put in a longer rod...and change cam timing and LOSE compression...but that's a whole other can of worms.

But...as I said...rod length outside of any other changes will add some torque...but the change will be minimal....it will reduce the side load on the piston skirt....how much and to what benefit...IDK....especially without changing anything else....can't see much difference in that with a .020" or whatever longer rod....

Now...stroke...that's a whole nother animal....a little goes a long way because the increase is in the swept volume and doubled....because the piston moves more in both directions.

And long rod engines are traditionally torque engines while short rod engines are high rev. (Of course ...usually stroke and rod length go hand in hand.)

Sooo...for example..those formula one cars have only like a 1 1/2" stroke and turn like 10,000 rpms.
 

Flyinhillbilly

The great cornholio
Messages
2,468
Reaction score
132
Location
North West Arkansas
I think you mean long stroke and short stroke. A longer rod also reduces piston speed, and decreases rod angle.

I clicked on this thinking I might get to preach, but I'm clearly late to the party.
 
Status
Not open for further replies.
Top