new predator 212

Status
Not open for further replies.

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
i got a new predator 212 , removed the governor was revving high and going high 40s to low 50s mph and fast acceleration . then it started going about 42 mph with slower acceleration . this happened with about 5 rides mixed with rough trails and street. what could have caused this? i admit i didnt break the engine in according to the manual , and the chain got looser since the first few rides not sure if this has anything to do with it. :confused:
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
i admit i didnt break the engine in according to the manual

That's what it's there for, to prevent damage to the engine, which is probably what you've done... Did you change the oil yet? If not, do it now (or, at least, before your next ride :D) Once you've done that, take it easy for a while
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
I broke it in for 30 minutes with 20w 50 oil and then went to 10w 30. not sure why i should go easy on it?
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Many people do not break in new engines. It is not really required, and if anything, yout motor should make a little more power after a few hours use because everthing has loosened up a little and the rings are properly seated.

If that oil was not reccomended in the manual it could have caused some damage. Still got yer warranty?
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
Many people do not break in new engines. It is not really required
:iagree:
For example...
A generator (among others) engine has no manual throttle control.
It's either running full bore or not running at all. That said, how does one break in a generator engine?
Also, so called "break in oils" are generally of lighter weight...not heavier!

Chain probably got loose from heating up and expanding.
Assuming a chain got hot enough (unlikely), then yes, it would expand. However, once it cooled off it would then return to it's original length. That's not what happens.

A new chain loosens quickly until it wears/breaks in.
Chainsaw chain is the best example of this.
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
i took the governor off before i broke it in. i am going to change the oil in it today and hopefully it is not damaged. it is still covered by the warranty. what kind of damage should i look for? is the damage something visible?
 

carter

New member
Messages
390
Reaction score
1
Me too. Warranties are for manufacturer defects. Once you decided to (a) pull the governor, and (b) go right out and beat on it - imho any engine damage is yours to deal with / learn from.

If he doesn't have to suffer the consequence of his actions why should he? It's not like he hurts anyone by doing this. I'll agree that it really wasn't smart to remove the governor in a brand new engine and put oil in it that is over twice the weight of what it was meant to use.
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
i opened up the engine an found the governor washer and some metal shavings. the motor was already leaking gas from the carb but i did a small fix that will keep not leaking until i need to take it apart. i believe that justifies the warranty.
 

carter

New member
Messages
390
Reaction score
1
Why didn't you send it back when you found all that? Were the metal shavings your fault?
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
i tried running it again with fresh oil and a new throttle setup. it goes straight to full throttle easier than the old set up. my chain is still very loose i believe it is what is causing the slower acceleration and slower top speed. it used to be tight when i first had the motor. i have it in fixed motor mount holes. i am going to try mounting it on the slots to the left of my holes and moving it up to tighten the chain. hopefuly the chain stays on if this fixes my problem then i will keep the engine.
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
The metal shavings is why the break-in process is necessary. The thinner oil gets splattered around the engine & collects all of this shrapnel & removes it when you change the oil
 

jamyers

Well-known member
Messages
1,444
Reaction score
49
Location
Buffalo Gap, TX
I wrote and deleted my thoughts about the ethics of claiming warranty at this point, all I'll say is that I think it's questionable - and who wants that?

Moving along...

...my chain is still very loose i believe it is what is causing the slower acceleration and slower top speed. ...

Nope. The only way a chain would affect performance was if it was so tight it was overloading the bearings and causing drag -and it'd have to be really really tight, or if it was so loose that it came off. All the chain does is transmit power. If there's an issue with acceleration or speed, look at the engine.

My bet is that (1) your first throttle setup came loose somehow and 'tricked' you into thinking you'd lost power, or (2) by overspeeding it you've scored the piston / cylinder walls and/or rod / crank bearing surface, and it's running "better" now because it has knocked the worst of the scored parts down. If so, it may well run for years like that, or it may go ahead and seize up tomorrow.

The only way to know for sure is to open it back up and take a close look.
 

beansdaddy78

JR. Member
Messages
565
Reaction score
2
Location
Carbondale IL.
I'm thinking of getting one of these for my stepsons Kart, he wants to try to race and I figure I can start him with a new motor so that I don't feel awful if something that I work on or if this jail ling 5.5 clone I bought for $5 fails on him in a race, especially his first race.

How much was the total cost of the motor with coupon?

Would you recommend it ?
 
Status
Not open for further replies.
Top