New guy with engine questions

Status
Not open for further replies.

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Given that the governor has influence on the throttle butterfly at all times, it IS possible the governor is causing the idle issue. It is a very common misconception that the only thing the governor does is to limit maximum RPM. This is not at all true. So- your governor could be out of whack. Or something else is off...
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
No picture required. Look at the carb- you'll see a rod and spring (or similar) coming off the throttle butterfly. follow those linkages, and you follow the governor system. when you reach the shaft that protrudes thru the block you've viewed the entire external portion of the governor system. The rest is inside the crankcase. What's inside the case is nonadjustable, and requires no adjustment.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
IF the governor is the problem, you're going to need to locate a service manual for adjustment. Where the shaft protrudes thru the block is the first adjustment point. Another adjustment point is where the upper limit screw is. Depending on your engines there may be other adjustments necessary. Don't rule out bent or worn springs, either- they can cause problems.
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
Haven't had time to check it out lately but I was wondering if it's possible to convert this to electric start. If so, how much would it cost and where would I get parts? I plan on adding a battery that I can charge every once in a while anyways and thought it would be nice to have electric start.
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
Some recent pictures:
Carb before cleaning:


After:


Inline Fuel Filter:
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
I took a look at the carb today and didn't see anything I could adjust. I took some pictures so you guys could see the carb a little better and help me out. Also, what is the screw under the idle screw for? I'm about to just save up for a new carb if I can't figure out whats wrong. :surrender:

Pics:


 

slideways

New member
Messages
575
Reaction score
6
That is one crappy camera. I'm not sure if you are trying to decide if your are missing linkages or what but this doesn't really help see what is missing because its so dark and hazy.
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
Sorry about the bad pictures, my phone's camera sucks and there's not much light in my garage.

1) I think the problem is that the throttle valve is a little loose in its seat, so the engine's vibration might be messing with it. The engine also seems to shake alot in idle, so I think I'm going to have the crankshaft and flywheel checked to see if its out of balance.

2) Should I try having the carb rebuilt or would it be better to just buy a new one?

3) The engine is really hard to turn on the compression cycle, so bad that the drill I have can barely turn it through the compression cycle and it almost pulls the cord out of your hand when you try to start it. Is this ok, or is there a problem there? It doesn't do this when the spark plug is out so I don't think its too much of a problem.

4) How much $$ is it to have the engine rebuilt and possibly upgraded for more horsepower?

I don't want to just give up and get a new engine, so please help me figure out how to what's wrong.
 

slideways

New member
Messages
575
Reaction score
6
If you have someone else doing the work it will certainly cost you more than a new motor.

Willing to bet that the compression issue is a valve lash problem. Either that or you have the key sheared but i've never seen that in a stock go kart motor. Mostly happens to mower engines when they hit a rock.

The only thing that may remedy the butterfly shaft play is to take the carb off and clean it and dry it completely. Then put a little bit of black RTV silicone on the top of the carb under that home plate shaped piece and slowly work it back and forth over and over and over again as it dries. This will form a new air seal that is still movable. If you let it set too long it won't be movable anymore and the carb is junk.
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
Thanks for the help, I fixed the valve lash and it starts a lot better now, it was way too big of a gap. Still have the idling problem, but that is probably the governor. It also seems to shake a lot, so I'm gonna check the flywheel to see if there is anything wrong with that. Got some new pictures with my new camera, so maybe you guys can tell if anything looks wrong.











 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
My CVT belt broke but I can't seem to find somewhere to buy one. I would prefer to buy from a store. I live in Indiana, does anybody know a place to buy a cvt belt here.
 

cumminsbayou4x4

New member
Messages
829
Reaction score
3
Location
fairhope alabama
tractor suppily has them they have 2 size so bring the old one with you id put the lawn mower motor in it dude it sounds cool and it would be easy just change the pullys on the motor and transmion the thng would be beaste with gears and lawn mower tires id diffenttily do it the tecumsas gonna be problems and if you dont want to put the lawn mower motor on it then atleste go get a harbor fright motor for it
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
I couldn't find the right size last time I checked but I will look again. Also, I don't think those types of belts work for the CVT.
 
Status
Not open for further replies.
Top