New guy with engine questions

Status
Not open for further replies.

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
Hey everybody, just got my first go kart. :wai: I've always wanted one, but I don't know a whole lot about the little one cylinder engines. I've worked with larger car engines, but never with this small of an engine. To start off, it's a Murray Hard-Drive Go Kart with the 6hp Tecumseh engine. I managed to get it up and running a few days ago and was able to drive it around a little. Then today I tried to start it up but it wouldn't. The first few minutes it would run for a few seconds then die. I then got it finally running after about ten minutes but as soon as I touched the gas, it died. I got it started one more time but died again when I tried to move the throttle. Now it won't even start up at all now matter how much I try. I hadn't done anything to the engine itself since it was last running. The only difference between now and when it last ran is the temperature. It was about 45 or so the last time I had it running. It's a little below freezing now.I looked in the carb, but didn't see any buildup, so it should be getting gas, and it's also getting spark. I really don't know what the problem is so any suggestions would be appreciated.
Next question is about an engine swap. I'm thinking about using the engine, transmission, and differential from a mower. The mower I have is an Agco Allis 1716H lawnmower with a 16hp engine. Would the trans and diff from the mower stand up to the speeds of a go kart? Link to identical mower: http://www.fastline.com/v100/1996-A...ail-db81b10f-e3a6-4949-882a-b2f33bc0aaaf.aspx

Go kart pictures:







 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
You've got a nice CVT on that thing. IMO, you should keep the driveline pretty much as is. If I was putting money down, I'd say your carb ingested a chunk of crap and is now in need of cleaning.
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
Thanks for the reply, I was hoping that wasn't the problem. Guess I'l have to start messing with it tomorrow.
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
Also, the reason for the engine swap is for a little more power, electric start, and ability to hook up lights and such with a battery.
 

slideways

New member
Messages
575
Reaction score
6
Gonna be tough to shoehorn that drive system into that small of an area. Plus when you use a riding mower trans you need to change the pulleys which makes the internals of the transmission move faster, wear faster, get hotter, and ultimately fail. The best thing i'd say is to clean the carb out and ride it like it is. That looks like a nice setup you have so if you were to swap engines i'd be looking at a clone motor with some mods done to put you in the 10hp range. Plenty of fun at that point.
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
Alright, so I think I'll just stick with what I got then. When I clean the carb, should I boil in lemon juice or just let it soak for a while? And will the lemon juice hurt the rubber in the carb? I don't want to forget how it goes together or break it because I've never taken the carb apart before, so I would prefer not to have to take it apart too far and possibly mess something up.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
It's a Techumseh carb. There's not too many pieces in it. Installing the float valve can be tricky but it's not too hard. I boiled mine today but I don't know if it worked yet and What I did was remove the float bowl along with the valve too and boiled it with a bottle of lemon juice.
 

slideways

New member
Messages
575
Reaction score
6
I wouldnt do the boil thing. Especially not right away. Just remember how the linkage went.. take a picture or 10. Then remove the carb and start taking it apart. The only thing you'll need to do is take the bowl nut off of the bottom. That gets you inside. Take a small amount of compressed air and some carb cleaner and spray through every hole in it. Take special care in the bowl nut itself because it has a hole that goes through it that has to be clear for it to run.

Drain all the gas out of the tank and put fresh stuff in also. It may be part of your issue if it was sitting before being sold. Gas goes bad in a month if it doesnt have stabilizer in it.
 

slideways

New member
Messages
575
Reaction score
6
Yea that should work.. probably 3/16 fuel line but you should be able to wiggle it in there.

Try continually priming it while its running to keep it running. Sometimes i have to do that with the Tec's just to warm them up. They are a very cold blooded motor.
 

slideways

New member
Messages
575
Reaction score
6
Yea it usually trickles in a little. Make sure both screws are in the air filter because they are a part of the primer air system.
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
What do you mean? The only screw on the air filter is what the plastic piece screws on to hold on the filter.

EDIT: Never mind I figured it out.
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
Ok, I cleaned out the carb with some carb cleaner and it runs now. I also installed a fuel filter and put new fuel lines on it. The problem is that the engine takes about 5 or 6 pulls along with the primer bulb to get going. The idle is uneven and sometimes the idle will start going higher and higher until I bump the throttle or kill the engine. The carb is all cleaned out and the throttle arm (not sure what its called) doesn't stick or anything. Anybody know what the problem could be? I tried adjusting the idle screw out when it revs higher but the engine dies after a few seconds and won't start unless I turn the idle screw back in.
 

FlatFootRacing

Speed Freak
Messages
52
Reaction score
0
Location
Easley, SC
Sounds like you govenor is out of whack! The throttle by default should be in the WOT position until you start it, then the govenor kicks in and throttles you back down!
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
if this is an adjustable carb, i suggest you remember your adjustments or start over and adjust the carb. sounds like it needs a good adjusting
 

91blaze

New member
Messages
87
Reaction score
1
Location
Indiana
The only adjustment on the carb is the idle adjustment screw and I don't know how the governor could effect idle. I think I can live with it for now because it only acts up at idle and seems to run fine otherwise.
 
Status
Not open for further replies.
Top