murray hard drive jackshaft???

Status
Not open for further replies.

exopo

New member
Messages
11
Reaction score
0
hello all just so you know im new and have been watching these forums for a while, and just bought a murray hard drive that needs a jackshaft. i need all the help i can any reccomendations what i need or help with one that fits all help welcome :D
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Right on landuse :thumbsup:

We're going to need a lot more detail if we are to offer you the best help we can. Telling us what type of kart it is means nothing; previous owners could have done anything to it. Include some pics too...
 

exopo

New member
Messages
11
Reaction score
0
awaiting arrival

i just bought it, and it is getting dropped off this afternoon. all that was said is it needs chains and a jackshaft
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Ok, cool. Once it arrives, give it a good once over, take some pics & get back to us. Take your time, we'll still be here :thumbsup:
 

exopo

New member
Messages
11
Reaction score
0
Alright so I took pictures but was unable to post.. I worked on it all day putting a chain on adjusting motor fixing dents and such. But I have a new problem. I bypassed the jackshaft by running the chain from clutch to sprocket. Worked until I realized master link was not inatalled correctly. But my oroblem now is I believe my gearing is to high without jackshaft. So my question is should I change clutch and sprocket or install the jack shaft? Whats better for the speed aspect of it all? It was fast but I cant risk burning up a clutch. It was smoking but appears fine to use still
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
What you are going to have to do is give us the tooth count on the clutch as well as the axle. If you are geared too high, you can either get a smaller cluth tooth count, a large axle sprocket, or use a jackshaft.

Sometimes getting a smaller clutch or larger axle sprocket is just not practical due to ground clearance issues. If this is the case with you, you will have to use the jackshaft again. You don't want to be buying a new clutch every month.

Your ratio has to be at least 6:1 or lower. Post some pics of your setup and we can help you further. We need to know the specifics

Here is how to post pics

http://www.diygokarts.com/vb/showthread.php?t=735
 

exopo

New member
Messages
11
Reaction score
0
jackshafts

images of jackshaft :auto:
 

Attachments

  • 2012-08-04_13.00.12.jpg
    2012-08-04_13.00.12.jpg
    83.4 KB · Views: 24
  • 2012-08-04_13.00.19.jpg
    2012-08-04_13.00.19.jpg
    103.8 KB · Views: 29
  • 2012-08-04_13.00.44.jpg
    2012-08-04_13.00.44.jpg
    105.5 KB · Views: 26
  • 2012-08-04_13.00.50.jpg
    2012-08-04_13.00.50.jpg
    110.3 KB · Views: 20
  • 2012-08-04_13.01.03.jpg
    2012-08-04_13.01.03.jpg
    135.1 KB · Views: 35

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
What you are going to have to do is give us the tooth count on the clutch as well as the axle. If you are geared too high, you can either get a smaller cluth tooth count, a large axle sprocket, or use a jackshaft.

Give us all the tooth counts before we can give you a better answer. Also give us the counts on the jackshaft as well. This way we can see what your ratio is supposed to be in stock form
 

exopo

New member
Messages
11
Reaction score
0
Well its been a while and I fixed that but now I have a new problem!
 
Status
Not open for further replies.
Top