Low Top Speed

Status
Not open for further replies.

npragin

New member
Messages
19
Reaction score
0
You can remove the governor and swap a sprocket and be fine. The stock valve springs limit RPMs to speeds where Con Rods and Flywheels generally don't come apart. Advancing the timing still doesn't change that RPM limit, but if you aren't reaching valve float RPMs... Advacing the timing will shift power from lower RPMs to higher RPMs allowing a higher max RPM and higher top speed (at the expense of some low end power, but you've got a TC so that is a low end multiplier).

Swapping in stiffer valve springs allows more RPMs. At these RPMs, Con Rods will come apart.. And at higher 7000+ RPMs, a flywheel or two has exploded, but not very often. Stock springs means no need for billet parts

I am not sure if I will get stiffer springs and reinforce the engine or not, but if I were to, what parts would I need to get? Is there a video or article outlining all of the steps and parts I need?
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
Honestly, with the stock camshaft and a genuine Honda rod, you can almost use gearing as a rev limiter.

Let's say the Rod is good to about 5800RPMs.
Let's also say that engine CAN'T push that kart 47mph.
48T:12T
30 series TC
6"Driven
10" Tires
18lb valve springs

5800 RPM = 47.6mph
You won't ever reach that, unless going down hill or free revving.

The safe answer is 18lb valve springs, an ARC billet connecting rod (stock length, or longer for more compression), and like 54:12 with TC. Optional High flow filter, free flowing exhaust, offset timing key,.. )

Let me bleed my brakes, then if nobody shows you good videos of valve springs and connecting rods I will when I come back.
 

Nosandwich

The REAL Poboy
Messages
873
Reaction score
22
Location
WHITE SETTLEMENT
Honestly, with the stock camshaft and a genuine Honda rod, you can almost use gearing as a rev limiter.

Let's say the Rod is good to about 5800RPMs.
Let's also say that engine CAN'T push that kart 47mph.
48T:12T
30 series TC
6"Driven
10" Tires
18lb valve springs

5800 RPM = 47.6mph
You won't ever reach that, unless going down hill or free revving.

The safe answer is 18lb valve springs, an ARC billet connecting rod (stock length, or longer for more compression), and like 54:12 with TC. Optional High flow filter, free flowing exhaust, offset timing key,.. )

Let me bleed my brakes, then if nobody shows you good videos of valve springs and connecting rods I will when I come back.

Goooleeee! You'd almost think reading this, this guy knew what he was talking about!

Just kidding, there are 2 pieces of advice you can take to the bank: Bob's and Itsid's.
 

npragin

New member
Messages
19
Reaction score
0
Honestly, with the stock camshaft and a genuine Honda rod, you can almost use gearing as a rev limiter.

Let's say the Rod is good to about 5800RPMs.
Let's also say that engine CAN'T push that kart 47mph.
48T:12T
30 series TC
6"Driven
10" Tires
18lb valve springs

5800 RPM = 47.6mph
You won't ever reach that, unless going down hill or free revving.

The safe answer is 18lb valve springs, an ARC billet connecting rod (stock length, or longer for more compression), and like 54:12 with TC. Optional High flow filter, free flowing exhaust, offset timing key,.. )

Let me bleed my brakes, then if nobody shows you good videos of valve springs and connecting rods I will when I come back.

Why would I not be able to reach that speed? Would it be possible with a higher horsepower engine? Or is it limited due to a different factor.

---------- Post added at 03:02 PM ---------- Previous post was at 02:45 PM ----------

Also, I am going to be running a one-wheel drive system, but I am not sure if I can mount a sprocket on to my rear wheel. The wheel is a DWT 706-08B wheel. I haven't seen any pictures on the other side so I am not sure if it is possible to mount my 60T on it.
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Why not start with the governor removal & high air flow kit & see how it goes; if/when you get bored with that setup, then consider upgrading internals...
 

Kansaskart

New member
Messages
452
Reaction score
9
I ran a 212 with no govenor and no internal mods all summer with no problems I weight 250 and for $100 not that big a deal, well except for kids. Now the kid down the road only knows wide open 8 hours a day. He also has a collection of atvs with blown engines.
 

npragin

New member
Messages
19
Reaction score
0
Does anybody know why I would not be able to reach the 45 miles per hour? I’m not expecting too I’m just curious. Is it because of a low torque or horsepower of the engine?
 

Dustin2017

SPP_MN
Messages
82
Reaction score
4
Location
Sweet home Oregon
I think having more fun would be slower speeds. Why you worried how fast you can go? Wanna go fast go get a shifter kart.slower speeds you can do cookies and go threw your neighbors yards and ect.lol
 

Nosandwich

The REAL Poboy
Messages
873
Reaction score
22
Location
WHITE SETTLEMENT
Here's a thought: go out to the driveway, put in the key, and go as fast as you **** well please.

I'm getting a little weary of all this " how can I make my kart faster/ life shorter crap."
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
Does anybody know why I would not be able to reach the 45 miles per hour? I’m not expecting too I’m just curious. Is it because of a low torque or horsepower of the engine?

Need a bigger, or modified engine.

The powerband of the gx200 is like 2k RPM peak torque and say 4k RPM peak HP. When the kart is geared for the amount of torque the engine puts out, you'll run out of power before the RPMs get high enough to reach 45mph. The power needed to accelerate any further becomes more than than the engine and gearing are providing the axle. The engine HP drops as RPMs increase past the Peak, as friction and drag are increasing on the chassis. Just not making enough power at those high RPMs to continue to accelerate the kart with that gearing.

Shifting the powerband to higher RPMs will help give you the power where you need it. With a Bigger Carb, performance cam, advanced ignition timing, high stall Driver Clutch,... you can the shift power band to like 4k RPM peak torque, 6000 RPM peak HP, and it will spin out to like 7000 RPM.

60T:12T with TC ... 46mph at 7000 RPM

Gearing so 44mph is at 4k RPM (Peak HP stockish engine) Means Running 36T:12T with the TC. That means you are probably going to burn up belts. Acceleration will be much slower and it might take forever to get up to speed, IF you ever get there. Might never shift into overdrive. Because the engine doesn't make enough torque to run that ratio.

A larger engine will have more torque so it can run a faster gear ratio. So maybe a 390cc could handle 36:12 with a TC and 10" tires.
44mph at 4500RPM.

I'm sure ^ is not very clear, but that's how my brain works.
BTW... This is all based of anecdotal evidence. I don't have a small kart. I've never had 10" Tires. This is blurry and hand-wavy math where I mentally weigh whether a kart will accelerate or not.

You might be able to run 48:12 with TC and 10" tires and turn 5500 RPM with stock springs. That would give you 45mph. Not sure you'll have the power with a stock engine. Not 100% sure you won't. Valve float normally happens around 5200-5500ish RPMs with stock springs, IF you have the power and gearing to reach valve float RPMs.

All that without a pic or mention of weight.
I need a nap now.
 
Status
Not open for further replies.
Top