How do you remove that.. blade holder?

Status
Not open for further replies.

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
well im working on a mower with a stuck intake valve, so I need to get up in the cylinder to get it free. i cant open the crankcase because there's this coupling on the shaft which holds the blade in place. is there a certain screw to take out, so what? i cant get the engine open with this thing in the way.

its a Honda Ohc model v shaft. can i just take the other end off where the flywheel was? there's a rubber seal blocking the shaft on that side.
 

souperman000

New member
Messages
2,466
Reaction score
11
Location
Westlake Village, CA
:useless:

Oh, I've always wanted to use that...sorry. Can you get a good pic of the place you are talking about? Do you want to blade off or what? Not quite clear on what you are asking.
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
Do you really need to take the side cover off to fix a stuck valve? If you are careful I bet you could keep the valve timing set properly.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
yes it's stuck in there. the spring retracts and everything, just no retraction of the valve. ive tried pulling it back with pliers and cleaning it with Xylene, but no luck. if i could just get this thing off the shaft, id be in like flynn.
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
That still doesn't answer why you need to remove the side cover. You're trying to remove the valves which are in the head, what is in the crank case that needs to be accessed?
 

Iron John

New member
Messages
397
Reaction score
27
Location
NA
You probably need to significanlty heat the hub. Get it red hot and as it cools to a dull red, touch a wax candle to the end of the shaft. Beeswax is best.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
before i got a puller, i used to thread in the bolt a little, pick up the engine by the shaft and beat the bolt really hard. should knock it off.

if the valve is stuck you dont need to do anything in the crank case, though. all youre going to do is ruin the crank case gasket for no reason
 

porsche930dude

New member
Messages
906
Reaction score
29
Location
Upstate, NY
im not real familiar with those engines but isnt it an ohv engine? you shouldnt need to get into the case.
put the screw in loose and use a 2 jaw puller with some heat. the blade holder comes off easy compared to the pulley above it. pb blaster is your freind
 

Iron John

New member
Messages
397
Reaction score
27
Location
NA
Heat yes, hot but not red hot. Dont want to f- the crank shaft.
Wax no...

why wax?

As Souperman said, it is an old trick and it actually works better than any penetrating oil. Wax has long skinny molecules that wick into the nooks and crannies created when you heat the outer part, and wax can withstand a higher temperature.

You do not have to worry about hrting the crank if you correctly apply the heat. You apply the heat to the outside of the hub, not to the crank. The outer hub expands away from the crank. The hub gets red hot - the crank does not. The crank will get hot, but not enough to hurt it - as long as you keep the torch on the outer flanks of the hub, and not the end. Afterwards, let the crank cool naturally. Do not quench it or do anything to cause one side to cool faster than the other.

You also do not have to jump right to red heat. Start low and then go as far as you need, comfortable in the knowledge that if done properly you will be OK.
 

slideways

New member
Messages
575
Reaction score
6
If this really is one of the newer Honda OHC engines they are a nightmare. The case splits in half allowing all of the internals and the timing belt to scatter about. Its not like your normal OHV or Flathead motor where you just pull the side cover off the crank and see how everything is inside.
 

Iron John

New member
Messages
397
Reaction score
27
Location
NA
i would avoid using any heat unless you really need to. that crank seal will be smoked

Usually, you can protect the seal by wrapping the inner end of the hub/crank with a wet rag. If you wrap it tightly and it is good and wet, the seal will not see above 212 fahrenheit.

You do need a good torch. Oxyacetylene with a fat tip so that you dump a lot of heat in the target zone (keep it moving) instead of slowly warming up the entire motor.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
Thank you slideways for understand the engine im dealing with, and thank you to everyone who replied. he's right. the case splits in 2 pieces and there is no detachable cylinder head on this model. i need to get in the case so i can use something to tap the valve in the opposite direction. believe me. i wish there was a head which i could simply remove.
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
Sounds like you have the GC series Honda.
Had mine apart several times for different reasons.
These power plants are a pain to disassemble.
Can you not just pull up on top of valve stem?
A few drops of acetone applied to valve guide may help to break up sludge that is causing stem to stick/hang.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
ok so i yanked it off with a puller, fixed the valve and now the engine is out of timing because i forgot about how in an OHV, the cam gears have a dot. however for those that misunderstood.. this is an OHC engine with a timing belt. now, the valves dont open/close at the right time, so i dont know.. is there a mark? will i have to open/reseal the crankcase?
 
Status
Not open for further replies.
Top