Hot clutch!?

Status
Not open for further replies.

Dazv

New member
Messages
31
Reaction score
0
Location
England
Hi guys, so I got my first ever kart project working last night with some advice from guys on this forum but I've come across a clutch problem. The problem is the clutch got very hot and even seemed to produce some smoke! The gearing on the kart is 15 on the clutch and 63 on the sprocket. I believe it has 11inch tyers if that makes any difference? Any advice guys?
Thank you very much in advance

Darren
 

johnsonr81

New member
Messages
45
Reaction score
0
Location
Graham, WA
According to the gearing calculator, looks like you have a about a 4:1 ratio which is pretty low. The guys around here will tell you a 6:1 ratio is what to shoot for. Otherwise, you risk burning up your clutch which it sounds like might be happening.
 

Dazv

New member
Messages
31
Reaction score
0
Location
England
Ah ok so the cheapest option would be to change the rear sprocket but I would need a 90 tooth for 6:1! Would that not make the kart really slow? Thanks for the help

Darren
 

Half-breeder

"Edit" button removed
Messages
1,686
Reaction score
9
Depending the weight a 5:1 is doable... <300lbs total. I forseen u needing a JShaft. Think about ground clearance and gear diameter...
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
You can get a low tooth count clutch and 60T axle sprocket. The gear ratio you have at the moment is too HIGH. Low numbers means you are geared high. High numbers mean you are geared low. You will sacrifice speed, but with the ratio you have now you will never reach its potential speed anyway before the clutch burns out
 

Dazv

New member
Messages
31
Reaction score
0
Location
England
Thanks for the quick replies! If it were you guys what would you do? Also with the fixes you suggest what do you this the top end speed would be? Thank you very much for all the help!
 

chancer

&#596; &#613; &#592; u &#596; &#477; &#633;
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
I would get a 12 tooth clutch. That would give you 5.25:1. Yes most recommend 6:1 but I agree with half breeder 5:1 is possible. Going all the way to 6:1 will lower your top speed. So it is worth a try at 5.25:1. Did you say it DID in fact drive at 4:1 (15 and 63). If so I'd say 5.25:1 will work.
IMI motorsports in Colorado sells cheap 12 tooth clutches on ebay under IMIauctions for 23 bucks free shipping. I would start with that cheap clutch just in case it does not work and burns the clutch.
Fill out your profile: If we know where you are we can send you to nearby parts suppliers.
 

Half-breeder

"Edit" button removed
Messages
1,686
Reaction score
9
I'm guessing he's runnin a 1" shaft engine... no idea the chain #... so noway of tellin the smallest #T cc he can use/get...
 

Dazv

New member
Messages
31
Reaction score
0
Location
England
Hi guys this help is much appreciated! Yes it did drive with the current gearing, so you'd recommend just buying another clutch with 12teeth? Things seem to be a little more expensive over here in the uk as the cheapest clutch is around £30 which I think is 50 dollars so the cheaper the fix the better really. I think the engine has a 3/4inch drive shaft and it's a honda gx160. Thanks guys.

Darren
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
See.. that's why you should include the location in your profile ;)

Anywhoo..
tell me about european prices on parts,
I found, that buying a clutch (chain sprockets etc..) from an US based webshop (I used OMBwarehouse for that matter)
makes it a lot cheaper than buying locally, even though the shipping fees are a PITA.

BUT: for just a clutch... sometimes the UKKartStore on ebay sells clutches for a very reasonable price (and sometimes they don't :()
but check yourself maybe you're in luck this week and you can get a clutch for ~£20

OH, check your chainsize!
12T clutches are generally #35 3/4" shaft whereas 10T clutches are #40 chain 3/4" shaft
so buy the smallest toothcount clutch you can find, matching your chain.

you can still adjust with the axle sprocket, but you'll be safe regarding the clutch then,
especially since that also is the cheapest option for buying a clutch.. more teeth are most often more expensive than those ;)

'sid
 

Dazv

New member
Messages
31
Reaction score
0
Location
England
Ok cool I'll keep an eye out for another cheap clutch. I believe my chain size is 219? I just hope I don't have to start again buying a chain sprocket and clutch! So is a new clutch what you would recommend to fix my problem? Thanks a lot mate.

Darren
 

Dazv

New member
Messages
31
Reaction score
0
Location
England
Also another quick question, what the heck is pitch? Is it just chain size?? Cheers guys
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
219 chain?? you sure...
if so 15 is already about the smallest toothcount you can get (I thought you'd need 16 to be honest)

Pitch is the distance between two adjacent rivets of the chain (center roller distance)
for a 219 that's 7.77 mm (very odd pitch, neither imperial nor metric match... odd but works well :D)
imperial chain is easier
a #35 would be 3/8" (9.525mm)
#40, #41 would be 1/2" (4/8") (12.7mm
you see the pattern, right ;) first digit is eigths of an inch pitch.

Sooo.. the bad news.. 219 clutches are generally more expensive (uncommon chain on yard karts in the US)
uncommen to run a yard-kart-clutch on european race karts
(that commonly use 219 chains)

sooo while they are available, they're not the cheapest to get :(

if you clutch is toasted already.. you can safely buy a 90T axle sprocket
(I think I have sprockets up to 104Teeth for my kart which runs 11" rear wheels and 219 chain)

but, with 90T you should consider installing a sprocket/chain guard.
(that'd be ~9" outside diameter for the sprocket.. or 1" clearance on 11" wheels)

'sid
 

Dazv

New member
Messages
31
Reaction score
0
Location
England
Thanks for all the Info buddy, I've ordered a 90t sprocket and I'll see how that goes! I just hope the inner hole on the sprocket is the same as the one I already have as I had to make a custom sprocket carrier for it so I'm hoping it will fit on the same carrier!? There is so much to kart building but I guess your mistakes are the best way to learn, Haha thanks again.
 
Status
Not open for further replies.
Top