Honda G200 - EFI Conversion

Status
Not open for further replies.

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
Sorry.. I don't understand the question...
CDI are ALL DC (otherwise it'd be hard to charge the capacitor in the first place)
that's why they usually sit right next to a rectifier ;)

And yes, you still need a coil (the capacitor or thryristor in this case) the CDI module is basically the charging circuit only..

if you talk about the charging coil (not the ignition coil) then yes.. you also should have one.
Since although the Capacitor will charge happily from a battery and that's enough to provide a spark..
a chargingcoil is more reliable;
it'd be a pain if your tank's full and you're still stranded in the middle of nowhere because the battery died ;)

talking of which.. make sure you get a good rectifier unit as well.. the small single diodes that generally are mounted to industrial engines like that may not be sufficient.

'sid
 

NewbCarter

Member
Messages
403
Reaction score
4
Location
Solin , Croatia
I have attached the pictures of what the one i have which came from a Endress gen-set ... The black and red leads are for the killswitch .. the 4 other wires i cant identify ..

Tho im kinda confused then .. at least to what the AC / DC refers to ? Since online , there are examples of both AC and DC , like this here :
http://www.sascooters.co.za/wp-content/uploads/2014/08/acdc-cdi.png

And going from that it refers to the way it is powered ?

Anyways , yes i mean on the ignition coil . So the CDI creates an impuls with the charged up capacitor , which then discharges into the ignition coils primary to create the spark ?
 

Attachments

  • 20160519_164738.jpg
    20160519_164738.jpg
    229.4 KB · Views: 3
  • 20160519_164747.jpg
    20160519_164747.jpg
    243.7 KB · Views: 2

NewbCarter

Member
Messages
403
Reaction score
4
Location
Solin , Croatia
Todays work ! It really is ghetto mounted , but it works !
 

Attachments

  • IMG-20160521-WA0023.jpg
    IMG-20160521-WA0023.jpg
    297.8 KB · Views: 1
  • IMG-20160521-WA0019.jpg
    IMG-20160521-WA0019.jpg
    293.2 KB · Views: 1
  • IMG-20160521-WA0017.jpg
    IMG-20160521-WA0017.jpg
    259 KB · Views: 2
  • IMG-20160521-WA0008.jpg
    IMG-20160521-WA0008.jpg
    218.3 KB · Views: 2
  • IMG-20160521-WA0015.jpg
    IMG-20160521-WA0015.jpg
    230.4 KB · Views: 3
  • IMG-20160521-WA0037.jpg
    IMG-20160521-WA0037.jpg
    256.8 KB · Views: 3
  • 20160521_115512.jpg
    20160521_115512.jpg
    253.5 KB · Views: 1
  • IMG-20160521-WA0005.jpg
    IMG-20160521-WA0005.jpg
    251.5 KB · Views: 1
  • IMG-20160521-WA0010.jpg
    IMG-20160521-WA0010.jpg
    238.1 KB · Views: 1
  • IMG-20160521-WA0001.jpg
    IMG-20160521-WA0001.jpg
    297 KB · Views: 0

Toycrusher

New member
Messages
168
Reaction score
0
Location
Deep Deep South Texas
Great work so far! You definitely want that complete matched assembly for the integrated idle air control valve. It would be hard to get it to start without that control. I can't read the language your links are in, is that a return style fuel system on that motorcycle?
 

NewbCarter

Member
Messages
403
Reaction score
4
Location
Solin , Croatia
Great work so far! You definitely want that complete matched assembly for the integrated idle air control valve. It would be hard to get it to start without that control. I can't read the language your links are in, is that a return style fuel system on that motorcycle?

It does seem like it is , tho it is expensive ... im currently in talks with karte molim on a cheaper throtle body assembly ..

Tho question : cant i just move the throttle valve while starting it ( open the throttle ) and then phisically adjust the idle ? .

I suppose the idle valve does just that but automatically ?
 

Toycrusher

New member
Messages
168
Reaction score
0
Location
Deep Deep South Texas
The idle air control valve is usually a helix or spiral gear motor with a feedback circuit. It moves in steps and is quite helpful in starting and maintaining an idle. It let's you richen the fuel mixture without dumping extra fuel in that could cause the engine to run away
 

NewbCarter

Member
Messages
403
Reaction score
4
Location
Solin , Croatia
The idle air control valve is usually a helix or spiral gear motor with a feedback circuit. It moves in steps and is quite helpful in starting and maintaining an idle. It let's you richen the fuel mixture without dumping extra fuel in that could cause the engine to run away

So if i got it right , i hook its power up and the signal to the controller (since the feedback circuit is usually a part of the ECU ? ) and depending on throttle position ( 0 to 5% ) its going to adjust itself to match the AFR ?
 

Toycrusher

New member
Messages
168
Reaction score
0
Location
Deep Deep South Texas
I'm used to reading efi systems in operation while troubleshooting engines with running Issues. IAC motors are stepper motors and the computers regulate them to control airflow. As I've seen from various manufacturers, they pulse the valve to adjust it further open or closed when necessary, otherwise it sits idle. What the computer sees from the feedback circuit, I have no clue. Sorry
 

NewbCarter

Member
Messages
403
Reaction score
4
Location
Solin , Croatia
Hey guys , sorry for the slow progress ..

Some trouble recently , and im needed home , so much that i cant do anything but help around . ( mother was on a knee surgery ... )

As of the EFI project , im trying to get some $$ to get the parts i need , in the meantime experimenting with the Arduino programme .
 

Jfive

New member
Messages
645
Reaction score
1
Location
Great falls Montana
I'm curious to how to how this turns out. I personally would of gone with microsquirt just for size, ease of operation, ect but I have heard of people doing it this way. I came across a guy in NJ with a neat platform called rusefi that is open source and maybe a bit similar to this. Has some pretty good success and a few people willing to help it along the way. Keep up on it and hope it works out. Might check out Diyautotune for a individual injector bung setup they have. Would make the install pretty easy I'd think.

---------- Post added at 08:21 PM ---------- Previous post was at 08:18 PM ----------

Here is the link for ease https://www.diyautotune.com/product/weld-in-injector-bung-for-ev1-and-ev6-injectors/
 

NewbCarter

Member
Messages
403
Reaction score
4
Location
Solin , Croatia
Here is the thing .

All the work i have planned , and the what i managed to do , is for nothing .

While i was away and didnt check the engine all that often since i keep it at my grandfathers place ( big garage and a lot of tools so .. ) , they were moving stuff.

Pretty much cleaning up and what not , i put the engine on the table , and someone managed to knock it off , the engine landed on its side and punctured the block . Reason it got punctured is that as they were moving stuff , there was steel piping and block on the floor , i presume thats how it broke .

Il get some pictures tomorrow .. :censored:

In the meantime , i found this as a candidate replacement :
rhttp://www.njuskalo.hr/moto-agregati/motor-rotax-bombardier-500cc-oglas-19226261

Does anyone know a thing or two about these Rotax engines ?
 
Status
Not open for further replies.
Top