Hemi Predator issues (sort of)

Status
Not open for further replies.

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
Ahhh, timing!!!

Are you sure you have an 8° key? Stock timing is around 24°, so 8° should put you right there. UNLESS, it was installed backwards. I'm not sure it would even run that way, and certainly not anything close to "normal", but it might.

I would just quit jacking around, pull the air cleaner, hit the carb with brake or carb cleaner and pull the cord. If it starts immediately, there is a carb problem.

---------- Post added at 05:10 PM ---------- Previous post was at 04:56 PM ----------



.003 is MORE COMMON, especially on engines that start on the first pull.

Lash is at .003 right now. I initially set it at 3 then moved to 0 lash and now back to 3.

Ill have to check out the carb. I wouldnt have thought installing a longer rod and stock lift cam would have changed anything enough to require different jets etc for a previously good working carb setup.

---------- Post added at 07:16 PM ---------- Previous post was at 07:14 PM ----------

Yeah its an 8 degree key
Installed so that it advances the flywheel clockwise per instructions
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
Ok so ive opened the engine back up.
As i figured cam is lined up with the crank properly.
......but.......
Im seeing a small amount of discoloration on the crank.......
I dont recalll looking before so im guessing its simce the rod install.
The rod shows no discoloration but im not sure if the billet rod will discolor like a crank will......and this thing only ran like 5 mins with the new rod.

I didnt notice a *holy $#^! amount of anything in the oil to make me think anything real bad has happened.
Rod doesnt have any play on the crank either.

So is this discoloration on the crank normal??????
It could be from the previous rod....not sure. After all the stock rod doesnt even have bearings lol.

Pics are attached.

Thanks
 

Attachments

  • IMG_20170131_075808.jpg
    IMG_20170131_075808.jpg
    280.7 KB · Views: 4
  • IMG_20170131_075837.jpg
    IMG_20170131_075837.jpg
    294.1 KB · Views: 3
  • IMG_20170131_080003.jpg
    IMG_20170131_080003.jpg
    257.3 KB · Views: 4

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
And by does the discoloration seem normal in the context is this pretty common on predator cranks to be discolored typically. Obviously discoloration on the crank isnt a normal thing.

---------- Post added at 08:51 AM ---------- Previous post was at 08:30 AM ----------

Well im pretty sure the crank is and rod bearings are done.
Put it back together and fired it up.off the kart and i can definitely hear lots of noise from the crankcase.
Only thing it can be is the rod........
Guess im gonna have to buy a new crank, bearings, and rod bolts and try again.
What irritates me is that i measured oil clearances 3 times with two different sets of micrometers.........
I followed the rod torque procedure from arc exactly. Using a quality tested torque wrench.......

Well thats pretty much my luck.
After stewing over this for the last hour ive also realized that the cost of this rod is the same cost of the entire engine......
I should just buy 3 engines and run stock rods and flywheels til something lets go and just replace the entire engine........lol
 

gman3850

Member
Messages
405
Reaction score
4
Location
gilbert az
is the crank or bearings mared, aircooled cranks often have small amounts of discoloration where the rods connects.

but if your does it is because you didnt use a high quality assembly lube. some people say you can use oil but i prefer nice lucas or permatex assembly lube
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
Well I took the engine completely apart again. The bearings and the crank journal are both in good shape. I did find one of my lifters was sticking. When pushed up into the block it would take alot of presure on the push rod to get it loose so i swaped them around. and that seemed to help a little. Also pulled the head, and saw a small amount of oil pooled on the piston. Apparently the .010 head gasket doesnt seal worth a ****, so i put on a .045 fire ring head gasket and reassembled the engine.

I put oil in it and test rode the **** out of it for about 30minutes and to my surprise the rod never exited the block and the motor actually got much quieter.



Definitly need to do some carb tuning, off idle acceleration sucks but main jetting seems to be close. As it pulls like a raped ape up top. The carb I got comes with a stock E tube and a .18 pilot jet. So I'm thinking I'm going to need to buy a new E tube.
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
So once you put it all back together... Was it still hard to start. That was one of your original Concerns on this thread?
And I agree unless anyone is racing... No need To spend 300 bucks on internals.
Just buy 3 engines and beat them to Explosion!

Look What FHB is doing guys. Tell me he is not having as much fun as a guy would want to have. Other than Making the Hobby Expensive and YES learning. Little point to Making a 99 dollar engine cost 600 in the name of Fun.
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
Its still hard to start.
The weird part is that if i can crack the throttle 1/4 open it will start much easier and once running it returns to idle like it should and will hold idle.

2 things i think are carb related....
Hard to start
Low rpm acceleration jist flat out sucks.

---------- Post added at 09:13 PM ---------- Previous post was at 09:11 PM ----------

The box the carb came in from nr racing says it has a stock e tube and .18 pilot.

Is there anyone willing to share a very general sea level appropriate jetting and e tube combination to start off with.
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
I agree hillbilly.
Even the box says go to a .20 pilot for better acceleration. So thats a definite. I dont know how the stock e tube fits in the equation though
 

gman3850

Member
Messages
405
Reaction score
4
Location
gilbert az
With a black mamba jr cam, open exhaust , velocity stack with k&n filter, arc rod and flywheel my jetting was

38
120 e tube
Stock pilot

Had to crack a 1/4 throttle to start but ran great after
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
https://www.youtube.com/watch?v=e-UuFrOFlkU

Well its much quieter.
Now on to some tuning.....

---------- Post added at 01:52 PM ---------- Previous post was at 01:38 PM ----------

is the crank or bearings mared, aircooled cranks often have small amounts of discoloration where the rods connects.

but if your does it is because you didnt use a high quality assembly lube. some people say you can use oil but i prefer nice lucas or permatex assembly lube

I thought about this and I sure didn't use any assembly lube on the journal and bearings. I'm not sure why because I used it on the cam lobes and ends as well as lifters etc. I had a bottle of lucas assembly lube right on the bench.......
My dad stopped by right as I was installing the crank so I'm just gonna blame it on my lack of attention span and him messing with me LOL
 

outcrydrummer

KART ART
Messages
364
Reaction score
0
Location
Greensboro, NC
Your dog cracks me up.

I'm getting a dog harness mount this week.....should be interesting LOL

---------- Post added at 05:25 PM ---------- Previous post was at 05:18 PM ----------

Mad drifts yo!
Dude that thing is FAST!!

Thanks, I'm not quite satisfied with it yet. Instead of worrying about tuning the .650 CV carb I'm just going to buy the mikuni vm 22 carb and put that on next week. Also going to try and find a quality .010 - .020 head gasket to replace the .045 on it now and then set clutch engagement to 3800 rpm and let her eat.

She should be real quick then.
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
Ohhhh the doggy.:wai:

Sorry I like dogs better than people.

When does an engine blow up so I can advance to GO and collect my $20? LOL
 
Status
Not open for further replies.
Top