Gx200 crank removal

Status
Not open for further replies.

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Ok well I was going to remove my gx200 clone crankshaft to do a repair (havent decided how I am going to fix it yet, but I know it will involve a crank removal.)
Anyway, is there anything I should know? What I was planning to do:
1.Remove engine from kart
2.Remove recoil shroud
3.Drain oil
4.Remove side cover and camshaft
5.Take out spark plug and fill the cylinder with clean rope
6.Partially undo flywheel nut, and tap it with a happer with a few threads on to remove flywheel.
7.Undo con rod bolts, then take out crankshaft

Is this ok? For re assembly I was going to do the same but in reverse. I understand it is a good idea to torque the bolts to correct spec, and i was going to buy/borrow a torque wrench.
Do I need to reset timing on the rockers or do anything else? If so how?

Thanks
Rob
 

TorqueRanger

New member
Messages
257
Reaction score
1
Ok well I was going to remove my gx200 clone crankshaft to do a repair (havent decided how I am going to fix it yet, but I know it will involve a crank removal.)
Anyway, is there anything I should know? What I was planning to do:
1.Remove engine from kart
2.Remove recoil shroud
3.Drain oil
4.Remove side cover and camshaft
5.Take out spark plug and fill the cylinder with clean rope
6.Partially undo flywheel nut, and tap it with a happer with a few threads on to remove flywheel.
7.Undo con rod bolts, then take out crankshaft

Is this ok? For re assembly I was going to do the same but in reverse. I understand it is a good idea to torque the bolts to correct spec, and i was going to buy/borrow a torque wrench.
Do I need to reset timing on the rockers or do anything else? If so how?

Thanks
Rob


I use a grease or paint marker and mark everything so it goes back together the same way it came out..
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
I use a grease or paint marker and mark everything so it goes back together the same way it came out..

How do you mean? The only thing that could have more than one way to come out is the camshaft, isn't it? and that is already marked with the little line engraved into it.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Personally, I'd remove the flywheel before the side cover. Let's keep the crank and cam supported from both ends while we beat the flywheel off, shall we?
 

sexyvicta

New member
Messages
806
Reaction score
2
be careful when hiting the crank with a hammer. Even with a nut on its easy to damage the threaded bit. I've done it a couple of times. It's fixable but a pain in the bum. Use a knock off tool(basicaly a nut that covers the whole threaded portion), or a flywheel puller if you can
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Ok i will go easy on the smacking, and I will be sure not to hit the flywheel. I have neither a flywheel puller or that tool, but I do have a bearing puller, think that'l work?
Whilst I have thw flywheel off, is there any advantage of advancing the timing in an otherwise fairly stock clone (governor and straight pipe)
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
the way i do it is to turn the nut on till about one thread isint in, put a screwdriver/crowbar behind it and push ever so slightly forward, tap on the nut once and if it dosent come loose, use just a little more force, it will come off and then your can continue
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
if the lifters fall out when you take the cam out, the push rods will follow. in order to put them back in, you need to take the valve cover off after putting the cam back in, and put the rocker arms back on the push rods.

no big deal but its just an extra step.


i find that the best way to remove a flywheel without buying tools is to gently pry up with the key lined up, and tap the crank snout WITH THE NUT ON IT! should jump right off.

learned that from davesfarm^
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
OK thanks Blue for the info about the rockers. The valve lash doesnt need to be adjusted, right?

As far as the flywheel- I have removed 2 of these before (13hp clone and briggs 3hp) Neither of the engines have been re-assembled, so I wanted to check I was doing everything right for reassembly.

I might go an order a front cover gasket. If they are more than a few £ then CARD FTW!
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
nope the valve lash should stay the same as long as you put it back the same way it comes out!

if you have feeler guages it wouldnt hurt to check anyways
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Got the crank out today :) i also decided to strip down the whole motor. I may have milled the head a bit.
I will speak to my teacher tomorrow and see if he thinks it is fixable. If not its £20-30 for a new crank or £100 for a new motor.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
The crank is damaged where the keyway is. I will grab some pics in a minute.
I may mill the head and put a flat top piston in to increase compression and add a k+n or something, and rejet.
edit: Uploaded pics.
I saw that there was a gap between the crankcase side cover and the crankcase, which had obviously been leaking a bit of oil. I was hoping the internals looked ok!
Does my cylinder look ok?
As you can see my crank is badly damaged. I abuse my kart :( (Im only having fun lol)

I spoke to some guys at bobs 4 cycle. They said with a flat top piston, high flow filter, rejet and a longer duration cam I would reach 10hp (if setup right)
At the moment I have plenty of top speed on flats and downhill, but I want more hill power. I dont want to regear because sprockets are expensive in the UK, and I may as well be spending that money on some simple mods.
 

Attachments

  • SAM_0707.jpg
    SAM_0707.jpg
    117.9 KB · Views: 7
  • SAM_0708.jpg
    SAM_0708.jpg
    88.7 KB · Views: 5
  • SAM_0709.jpg
    SAM_0709.jpg
    77.9 KB · Views: 4
  • SAM_0710.jpg
    SAM_0710.jpg
    81.2 KB · Views: 23
  • SAM_0711.jpg
    SAM_0711.jpg
    71.1 KB · Views: 55
  • SAM_0712.jpg
    SAM_0712.jpg
    77.8 KB · Views: 5
  • SAM_0713.jpg
    SAM_0713.jpg
    62.1 KB · Views: 10
  • SAM_0714.jpg
    SAM_0714.jpg
    63.5 KB · Views: 3

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
I have a thread on here
http://karting.4cycle.com/showthread.php?t=408083
I thought I would ask your opinions. Has anyone used the bsp-1 cam, and is it worth it?also is my cylinder ok? The engine ran perfectly, but whilst I have it torn down...
Cheers
Edit: oh and today I started to lathe down my crank for a heat shrunk sleeve. The shaft is so soft... :arf:
 
Status
Not open for further replies.
Top