governor removed with pictures.

Status
Not open for further replies.

ironman

I'm Back!
Messages
906
Reaction score
2
Location
kentucky
ok guys thought it was time to try a few things.so today i removed the governor of my 5 h.p. b&s motor it wasnt as bad as i thought .i thought it would be a lot harder.
1.

crank cover 6 bolts hold it on.
2.

inside of motor
3.

crank cover inside here is the plastic gear you here about
4.

gear im takeing off pretty easy twist and pop off.
5.

gear taken off.
6.

this is the governor rod that i had to grind and shave down
so it dont hit nothing
7.

here is the lever that i cut off so it does not move and the inner parts of the motor
8.


9.

had to cut bracket down and connect to rod on the outside of the motor also ran a pin threw the rod to be on the safe side
10.

didnt know i would have to change the hook up on the linkage took a few minutes to figure it out but it work all out and its safe.:cheers2:
Sorry so long but i just thought that this might help a few people out. my speed increased from 27 to 34 thats 7 mph. just on my block going to take it to the school track sunday to see what i can get it up to.:auto:
 

rockstomper

New member
Messages
75
Reaction score
0
Looks like you did a good job there.I just removed the governor from our hf 6.5 the other day runs a lot better!!!! :thumbsup: :thumbsup:


Mike
 

ironman

I'm Back!
Messages
906
Reaction score
2
Location
kentucky
great watch out alot of people say you shouldnt take governor off because those motors have cheap parts in them,and at higher rpms motor will come apart. but ive talk to my local shop they told me they would be fine. let me know how your does and how fast you get it ok. this is always good info to know about first hand.i also have a h.f. motor
 
Last edited:

RobertD

Administrator
Staff member
Messages
3,018
Reaction score
75
Location
Texas
@ironman: shouldn't remove the governor b/c of cheap parts, or shouldn't open it up b/c of cheap parts?

NICE pics post!!!
 

rockstomper

New member
Messages
75
Reaction score
0
great watch out alot of people say you shouldnt becauue those motors have cheap parts in them but ive talk to my local shop they told me they would be fine. let me know how your does and how fast you get it ok. this is always good info to know about first hand.i also have a h.f. motor


Yea I hear that to,I have been looking at some other influences out there on this motor.There is a few that say don't do it then there is people that say it will be fine with that said I will have to find out for my self.

I am in the middle of rebuilding the cart now but it was clocked before the rebuild at 32 mph with a 5.0 Tecumseh,the clutch is a 10 tooth and the axle sprocket I think is a 52 (not sure is that's right) I will have to recount that one.


Mike (Rockstomper)
 

oscaryu1

New member
Messages
2,767
Reaction score
7
If it even gets that high...

You can run to around 4k RPM safely on those. Afterwards, oil consumption increases drastically, and you have a high chance of throwing a rod.

A billet 5HP rod is like $20 on eBay...
 

oscaryu1

New member
Messages
2,767
Reaction score
7
Look at picture 5. Notice that washer behind there? Remove it. Hopefully you have NOT started the engine, unless you like damage.

My GX200's governor looks exactly like yours (just not the metal arm)... And it had a washer behind there. And looking at yours, you have one too. I used a magnet to remove mine.
 

ironman

I'm Back!
Messages
906
Reaction score
2
Location
kentucky
hum.. no metal washer that i know of on there on picture 5 if you are taking about that rod it has a metal flat end on it has to stay on or oil will leak out.I even pulled it back off to double check thought id miss something but nope no washer.
 

athif

New member
Messages
112
Reaction score
1
wouldnt that shorten the life of the engine and potentially damage the parts?
 

kibble

I banned myself
Messages
2,766
Reaction score
18
wouldnt that shorten the life of the engine and potentially damage the parts?

But, OH! Think if how much more fun you can have without that treacherous little piece of machinery which is the governor!
 

ironman

I'm Back!
Messages
906
Reaction score
2
Location
kentucky
wouldnt that shorten the life of the engine and potentially damage the parts?

sure will.but thats the price you pay for speed.unless you got a built motor that is able to handle more.ill let you know when it blows.......:innocent:
 

gocartkid

Bad Attitude
Messages
329
Reaction score
1
Location
CT
What is the role of the plastic gear? I'm doing the same thing to my engine....can't you just take the rod out alltogether and seal the hole in the side of the block?
 

kibble

I banned myself
Messages
2,766
Reaction score
18
It's really not that complicated, and the plastic gear is part of the governor assembly, it gets removed if you remove the governor. You CAN take the rod completely out and find some way to seal the hole, but most people choose to leave the rod there as it's already covering the hole.
 
Status
Not open for further replies.
Top