? from a Noob..Clutch getting hot....

Status
Not open for further replies.

dudarino

New member
Messages
9
Reaction score
0
Ok, have read many threads which have helped me in my build. I bought a Thunder Kart frame with axles and sprocket and clutch included. Bought a 6.5Hp Predator from HF. My clutch has 10 teeth and sprocket has 54. Have 13" Tires(Though I measure them at 11").
Can not tell on sprocket or chain what size they are and from measurements it is to hard to differ from 1/8 and 5/32 to see if it is a 40 or 41...could be neither.
After running cart for about 5 minutes...at about 25 m.p.h. the clutch gets very hot....not smoking just hot to touch...about as hot as exhaust on engine...is this normal????

**Noticed today that it doesn't look like chain seats properly in the sprocket either....maybe these are different size sprocket and clutch teeth...they seem to measure the same though.

Thanks for posts on throttle linkage hook up and working on my kill switch now.
 

Attachments

  • Picture 001.jpg
    Picture 001.jpg
    99.9 KB · Views: 14
  • Picture 002.jpg
    Picture 002.jpg
    97.2 KB · Views: 21
  • Picture 003.jpg
    Picture 003.jpg
    99.5 KB · Views: 19
  • Picture 004.jpg
    Picture 004.jpg
    91.6 KB · Views: 12

dudarino

New member
Messages
9
Reaction score
0
Yes someone else has brought this up......so a sprocket with more teeth?

Also upon further troubleshooting I relize that the shaft is always turning even at idle...which I believe to be normal operation, but the clutch does slighty engage...if I where on a flat surface kart would inch forward....is this normal?

AND CLUTCH GETS HOT WHEN JUST SITTING THERE IDLING ENGINE WITH NO THROTTLE! IS THAT NORMAL? Maybe weak springs in the clutch? Any further guidance is appreciated!

*Oh yeah kill switch is operative thanks to posts from the experts (I went with the toggle switch not a push button since my kids are driving it). THANKS!
 

jeremybentham

New member
Messages
347
Reaction score
0
Location
Dutch Country
Yes someone else has brought this up......so a sprocket with more teeth?

Also upon further troubleshooting I relize that the shaft is always turning even at idle...which I believe to be normal operation, but the clutch does slighty engage...if I where on a flat surface kart would inch forward....is this normal?

AND CLUTCH GETS HOT WHEN JUST SITTING THERE IDLING ENGINE WITH NO THROTTLE! IS THAT NORMAL? Maybe weak springs in the clutch? Any further guidance is appreciated!

*Oh yeah kill switch is operative thanks to posts from the experts (I went with the toggle switch not a push button since my kids are driving it). THANKS!

Can you make it idle a wee bit lower? That would help combat premature engagement of the clutch.
Lube your clutch bushing. (the area where it bolts into the crank) A DROP OR 2!!! ATF, motor oil, chain lube, whatever you fancy.
DO NOT get ANY petroleum products inside the inner-workings of the clutch itself.
 

dudarino

New member
Messages
9
Reaction score
0
I did put some engine oil on the bushing yesterday and that did not seem to help the heat build up....Took it out today and the chain broke.....so since the sprocket does not have a size on it, I think next payday I may invest in a new sprocket, clutch, and chain so I know what size they all are to ensure they match.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
As for the 40/41 thing, they will both work, because they have the same pitch but different roller diameters.
 

dudarino

New member
Messages
9
Reaction score
0
Please someone answer this question.....after looking at some pictures on the internet it may look like my clutch is missing the bushing. When I take the snap ring off my clutch there is an outer shell and inner shell.....nothing else. Is that correct or should there be a bushing on the shaft to seperate the outer shell and inner shell???
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
The bushing is pressed into the outer shell, your chain in the first pictures was worn out, likely your clutch has been under stress due to excessive stopping/starting, holding the gas and brake at the same time, high idle, or a hilly area. 54t on that size tire shouldn't be hard enough to destroy a clutch very quickly.
 

dudarino

New member
Messages
9
Reaction score
0
How would I lower the idle of my engine?....or should I wait to see what how a new clutch reacts to it first?

Just to let you know when I bought the cart and the guy gave me the clutch and chain you could tell they had been sitting out in the weather for sometime.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
If you look on the carburetor, you will see a screw (sometimes with a spring coiled around it). You have the right screw IF- the the throttle arm (when swung toward the idle position) comes to rest against the tip of the screw. It is probably black and plastic, but not necessarily. This will be the only screw on the carb that you can see the tip of. This is the idle set screw. Turn this screw counterclockwise to lower the idle, clockwise to raise it. All this screw does is regulate how far closed the throttle plate rests.
 

strang

New member
Messages
19
Reaction score
0
Location
Gaston County, NC
My clutch has 10 teeth and sprocket has 54. Have 13" Tires(Though I measure them at 11").
Can not tell on sprocket or chain what size they are and from measurements it is to hard to differ from 1/8 and 5/32 to see if it is a 40 or 41...could be neither..
Most probably 41.

I have a Streaker kart, put a Predator on it and a new clutch (10T).
The clutch called for 41 and it fit the sprocket perfectly.
 

dudarino

New member
Messages
9
Reaction score
0
Ok so I finally got some time and replaced the clutch/sprocket/chain all to size 35 and 6:1 ratio 12t on clutch and 72 on sprocket. Well the clutch still gets hot as hell.....guess the idle needs adjusting but to a point that makes no sense since when i just let the engine idle the clutch never gets hot but as soon as I take it around the block it starts heating up.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Ouch! Yeah I think thats what he said, but I wouldn't worry because it's the standard setup for your bike and your putting a tc on soon anyway, right?
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
really? my warrior is geared 10:1 with 19" tires and i burnt my arm pretty bad. lol.
What centrifugal clutch are you using? Sprocket tooth counts and chain size please.

When discussing gokart ratios, it is assumed that 10" to 11" diameter tires are in use.
Ratios of 5:1 or 6:1 is considered the standard ratios to stay within.
Once the tire size gets beyond a certain point, the ratio should change to something larger.
10:1 may not be enough for 19" diameter tires. I can guarantee that you are not getting the most from your engine.
 

dudarino

New member
Messages
9
Reaction score
0
Well I myself have lowered throttle to lowest point before it stalls changed ratio to 6:1 and have relized clutch is going to get hot....so will weather it out and see how long it lasts! I did relize though the faster you go the cooler it stays....so I will just go fast! Thanks for all the input guys I do greatly appreciate it!
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
well my bike is geared super low. like once you get to 20-25 the engine has no load on it whatsoever.

i can go none to full speed in about 30 feet.

my 20 series driver is on its way... then i can get the TC set up.

yes going fast keeps it cooler... going slow makes the clutch shoes drag and make heat. full speed locks them up.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Hmm Once you get the tc that ratio will be fine- i have 1:6 with 19" tyres on my kart and a tc... Oops!
 
Status
Not open for further replies.
Top