free lawnmower

Status
Not open for further replies.

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
you think a 5hp briggs dipper would work?

well mines a taper shaft, pulley is rusted on good, and it has a slight wobble.

EDIT: also it would make the dipstick horisontal and it would definately leak out the worn seal.

No idea about the Briggs dipper, I haven't taken one apart for years. I doubt it would fit because the one in this has to lean forward quite a lot. It's worth a try if you've got a spare dipper.

Yep, I moved the dipstick so it was upright.



I just used a bit of pipe, easy as and didn't leak. Took ages to fill it up with oil though.



Thanks

Hayden
 

porsche930dude

New member
Messages
906
Reaction score
29
Location
Upstate, NY
One thing people never consider when converting to a horizontal shaft. The engines with an aluminum flywheel dont run smooth or at all without a blade to add flywheel weight. Try to run a lawnmower without its blade and see what i mean. Thats why vertical shaft engines always have a heavy cast iron flywheel
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
One thing people never consider when converting to a horizontal shaft. The engines with an aluminum flywheel dont run smooth or at all without a blade to add flywheel weight. Try to run a lawnmower without its blade and see what i mean. Thats why horizontal shaft engines always have a heavy cast iron flywheel

Fixed. ;)

Mine ran smooth and idled nicely with it's aluminium flywheel. The problem was getting it to start. If you didn't pull it as hard and as fast as you could, it'd just break your fingers when it back fired, or break the pull starter (its on it's 4th pull starter now). Don't convert one with a side starter like mine unless you have a huge stockpile of them, very weak starter. Luckily side starters are quite rare so you're unlikely to have an engine with one.

Thanks

Hayden
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
my 6hp briggs vertical has a cast iron flywheel, my 5.3 tecumseh vertical has a featherlight aluminum flywheel....
 

sexyvicta

New member
Messages
806
Reaction score
2
^was guna say that.

my tecumseh horizontal shaft engines have alloy flywheels

also i have started plenty of vertical shaft brigs engines with no blade/blade disk and they start and run fine
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
yes i believe most briggs use the same flywheels for both vertical and horisontal versions.

i was able to idle that 6hp briggs w/ blade SO low. also i was able to idle a 5hp briggs leaf blower insanely low that all you can hear is the valves ticking.
 

bighead

New member
Messages
4,022
Reaction score
54
Location
Pacific Northwest USA
One thing people never consider when converting to a horizontal shaft. The engines with an aluminum flywheel dont run smooth or at all without a blade to add flywheel weight. Try to run a lawnmower without its blade and see what i mean. Thats why vertical shaft engines always have a heavy cast iron flywheel



I heard you say this a few times. And everytime you said it members told you there engines ran fine.
 

porsche930dude

New member
Messages
906
Reaction score
29
Location
Upstate, NY
lol every mower is different. alls im saying is its something you have to consider before going through the trouble of converting one and scratching your head for a few weeks before figureing out why it ran good before and not now. Its mostly just the newer engines that have a superlight flywheel. The briggs 6.75 is one i know for sure
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
Basically, lighter flywheel=faster kart.
A little faster acceleration...top end will be no different. Only with a dyno reading could you prove the difference between the two flywheels.

yes i believe most briggs use the same flywheels for both vertical and horisontal versions.
Nope. Big difference between them.
Its mostly just the newer engines that have a superlight flywheel.
Virtually every vertical shaft mower engine I have serviced utilizes the lighter flywheels.
Only exception to this is the BBC engines.
 

karl

Well-known member
Messages
2,449
Reaction score
719
Location
North east Ohio
A week ago I put a flywheel from a vertical briggs 3.5hp classic and put it on a horizontal briggs 3hp go-kart motor. Huge throttle response difference, more power. I was doing about 5mph and hit the gas on the road and roasted the rear tire (1 wd) Also, it will do about 25-30mph. It is harder to start and dosent like to idle when cold, but it is well worth it.
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
A little faster acceleration...top end will be no different. Only with a dyno reading could you prove the difference between the two flywheels.

Yeah, pretty much. But I'l show everyone what difference it makes. Lets say a cast iron fly wheel weighs 1.5kg and the aluminium fly wheel weighs 0.5kg. Lets say the rest of the engines internals and clutch weigh 5 kg. That's a bit conservative I think but anyways.

The difference between 5.5 and 6.5 is 15.385%.

So your engine revs 15.385% quicker... But your kart doesn't accelerate that much faster. Say you have a 5:1 gear ratio.

15.385/5=3.077

Your kart, in an ideal world, will now accelerate about 3% faster.

That's not much, but all these little things add up.
 
Status
Not open for further replies.
Top