First go kart project need a lil help

Status
Not open for further replies.

zjbi87

New member
Messages
9
Reaction score
0
hi everyone this is my first go kart project and i need some help. ive done a good amount of research but still have a few questions.. ok so i have a pressure washer that i dont use with a gx390 honda motor.. so i looked around n found a go kart that id like to put it on.. i notice that the shaft is about 4 inches long or so on the motor.. now it appears to me that the clutch sits on the end of the shaft but i hear you want it as far in as you can get it.. how do you move the clutch further in on the shaft but also keep it from moving around? also the kart has what i would refer to as average go kart tires.. medium in the back smaller in the front.. what size tooth clutch do i need? im not after anything specific such as high top speed or fast exceleration i just want it to do what a average go kart does..

thanks for any help you all have!!
 

zjbi87

New member
Messages
9
Reaction score
0
adding to that

forgot to add that the sprocket is 55 tooth and the gap between tip to tip is 1/2 inch so i believe that means the chain needs to be #40? thanks!
 

zjbi87

New member
Messages
9
Reaction score
0
..

ok i think i understand the installation of the clutch now.. so i guess the clutch is moved up to the shaft shoulder and held in place by a set screw that holds in onto the keyway? can i use the keyway i have now that is almost the lenght of the shaft or do i use a shorter one?
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
You can cut the key shorter as needed, It only needs to be as long as the keyway in your clutch.

We could give you much better gearing advice if you posted how many inches tall your back tires are.

Also tell us if you'll be climbing hills/off roading or always riding on flat-hard ground.

It would probably also help us help you if you posted some pics of your kart, and include how much the rider (and passenger?) weigh.
 

zjbi87

New member
Messages
9
Reaction score
0
Some more info.. It's a light kart I'd guess about 80 lbs or so ..passenger weight would be about 185 lbs the tires say 4.10/3.50-5 back tires say 13x5.00-6 nhs It's just going to be for riding around mostly flat ground maybe some trails w some sugar sand
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
Here's a link to our speed calculator: http://www.diygokarts.com/speed-calculator.html

If you'll be doing any trail riding through thick sand I'd suggest gearing your kart for no faster than a 25mph top speed at 3600rpm. With your 13" tires and a 55-tooth axle sprocket that means using a 10-tooth clutch. But the drawback here is that all the 10-tooth clutch models available In 1" bore are outboard-only mounting style and would have the drive gear hanging way out past the end of your engines output shaft. (and you said you didn't want that)

On the other hand If you were just going to ride on flat/hard surfaces with no deep sand/hill climbing you could buy a Inboard-Outboard style 14-tooth clutch that could slide all the way onto your output shaft like you wanted.

The Noram 1600 clutch (for #40 chain size) comes in your choice of 10 or 14 tooth models, but take a look at the pics here: http://www.out2win.com/catalog/noram.html#1600
to see that the much smaller diameter of the 10 tooth drive gear requires the clutch to be an outboard-only mounting style that would have the drive gear located way out at the very end of your crank... Now compair that to the 14-tooth/Noram 1600 model and notice how its got a 1" hole all the way through so the clutch can slide all the way on, see what I mean?
 

zjbi87

New member
Messages
9
Reaction score
0
I see exactly what you mean.. Only reason I said I'd want it further down the shaft is I heard it's bad to have it far out.. Now if I were to set it up to go faster then 25 would I use a higher tooth clutch? It would probably flat ground 90% of the time n maybe some trails 10% But even the trails are mostly flat I live in florida so everythings flat lol
 

zjbi87

New member
Messages
9
Reaction score
0
Could I use a 17 tooth? If I'm only on flat ground? I see northern tool has a Hilliard 17 tooth 1 in bore 40/41 for $119
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
I wouldnt recommend any larger than a 14 tooth clutch for your current axle sprocket and rear tires. After pulling your governor you'd be geared to hit 49mph with a 14-t @ 5000rpm... Gearing any taller than a 14-t is just going to put way more stress on your clutch. Try if you want, but I think you'd burn up that 17 tooth.

Northern stocks a 14-tooth: http://www.northerntool.com/shop/tools/product_200415726_200415726 you could instal Inboard, but I'd spend a little more and go with a Noram 1600. If you shop around you'll probably find a lower price than that outlaw2win link I gave you. I think Noram clutches are better than Hillard and well worth the investment.
 

zjbi87

New member
Messages
9
Reaction score
0
Thanks man you've really been a great help .. I'll go with the 14 tooth .. You've answered all my questions now I can start my kart thanks a million
 
Status
Not open for further replies.
Top