Extra HP GX200?

Status
Not open for further replies.

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
I know the basic mods that can be done with these engines but what I'm actually trying to find out and nowhere I've looked gave a number of how much extra power you get. Base line I know the GX200 is about 6 1/2hp. How much extra HP and torque does doing governor delete, free flowing intake, exhaust actually add on? Not sure if anyone has actually had a dyno of some sort done but it could be helpful so one could choose one engine over another.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
since numbers are individuals...
two identical original GX200s can be modded by two differnet people using the same techniques and replacement parts and end up with a different hp rating.
as a minimal difference (air quality, fuel quality, mixture adjustment, mainjet size..even cone angle, air filter... endless list clipped) can add up to give very different results for what one would consider two identical engines.

there's a ballpark at best.
So if you want to know, there's no other way than to test that individual engine.

'sid
 

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
Kind of what I figured. Only figures I've seen was 3-4hp added after doing gov delete, air and exhaust. I guess price wise one could save money doing the GX200 then buy a slightly heavier GX270.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
you can throw tons of money at a gx200, enough to buy several gx390 actually..
then again, you can throw enough money at a gx390 as well,
ending up with a severe amount of horses (mid thirties) so...
I think main question will always be: what are you willing to spend, and what's it you're trying to achieve.

'sid
 

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
So true. I guess for those who don't race mild tune should be sufficient. Think maybe govenor delete isn't always needed maybe modifying it for a bit more rpm range but still keeping it installed.
 

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
Just trying to see if the GX200 will be enough engine to get me up to 30mph maybe 35mph. I'm looking to build the kart for mostly riding on the street since other than snowmobile trails I'm mostly limited to streets. I'm hoping with engine and myself to not be over 285lbs myself being 160lbs or so. I think 35mph is reasonable and being on the street with a smallish hill and a TC30 with a 14 tooth and a 54 on the live axle. 11" tires.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
I might as well say it. Your last two posts are just wrong....Just a quick look around and you'll see dozens of posts that will tell you either remove the governor or leave it alone.

And that's a pretty steep gear ratio, even for those fairly small tires...

I suggest you use the search feature so you can see how others have regretted "thinking" these were good ideas....
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
if by governor modifying you mean adjust it to maybe 4000 rpm, then yes.. maybe that's enough..
on an original Honda that number is still to be considered safe... on a clone(predator or alike) I wouldn't dare to even try...

If you on the other hand think you could reach 5k and still leave it inside the engine, then as Poboy said: you will regret it sooner or later (sooner in fact...)
the only sane set of options is to remove it or leave it untouched!

that ratio... with the fewest possible words can be described as "stupid"
you'll burn through belts in seconds; each belt representing roughly twenty bucks...
that's not a good plan at all!

'sid
 

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
Regarding the gear ratio it's close to what someone recommended in a FAQ http://www.diygokarts.com/vb/showthread.php?t=16353 so unless the individual was trying to misinform then someone should revise it to not confuse people later on. I'm not into Chinese knock offs by any meams, I've had way too many Chinese things break prematurely to know just to buy quality when needed so yeah I'm going true Honda.

I might have misread that sticky so please let me know. I'm not by any means opposed to running a 5:1 gear set since I'm sticking mostly on street.
 

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
Well we do learn over time. Fortunately I have time before I start on mine so glad I can do some research first before jumping in and messing something up bad and end up blowing more money than needed.

Just remembered that by state law I could get licensing to use ATV/Snowmobile trails one of which is about 120 yards away from my driveway. Just have to get plates like one would for a quad and then it's Street legal.
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Guys, have any of you actually had a go kart with a comet 30 series torque converter?

STOCK, the manco Baja 200 with a 5 hp briggs goes 35 mph at 3600 RPM.. so please don't just jump on the gearing bandwagon without checking your facts from reputable sources, and remember that torque converters do compensate to some degree for what a centrifugal clutch cant do.

If you just go off of MPH which accounts for TIRE SIZE, which I think you all have completely glazed over... you get

40 mph with 40 series torque converter,
8-9 hp full size 1 seat
10-13hp larger 2 seat go karts (bigger engines are more in the mini buggy category)

35 mph 5-8 hp small one seat 30 series torque converter 6" driven
28-30 mph two seat 30 series torque converter (some have 7" driven in this case)

25 mph centrifugal clutch, small go kart, flat places
15-17 mph centrifugal clutch, compound reduction jack-shaft, off road

Those tires (11") are very small, so 35 mph is a perfect speed for a small kart with 30 series TAV2. This may be oversimplifying things, but to keep it simple, just go off 1 or 2 seat, large or small, and go off the gearing that reputable go kart manufacturers have set them to.

Sources:
manco dingo/deuce 9-13 hp with 9t/54t and 22" tires 40 series
manco 485 5 hp with 9t/54t and 14.5" tires, 30 series
manco baja 200 5 hp with 9t/54t and 18" tires, 30 series
yerf dog 3203 with 6.5 hp 10t/60t and 20" tires, 30 series
most go karts with cent clutch 12t/72t or 10t/60t 3-6.5hp and 11-15" tires
baja heat/warrior with 19" tires, compound gearing unknown but you can look it up, cent clutch
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
There's a huge difference between your 6:1 ratios and his 3.8:1 ratio, don't you think?
And while I must admit, that even my very own calculator doesn't moan entering a 14->54 ratio for a lightweight kart with 11" wheels...
(so it's not nearly as "stupid" as I initially thought)

that simply smells "belt consuming" from miles away;
We can all be wrong of course.. but going with 10->54 at first (not spending a dollar)
to see how it goes,
before spending 10bucks on a 14T sprocket just to spend 20bucks on a new belt because our guts were right...
can't be too bad of an advice either ;)


'sid
 
Status
Not open for further replies.
Top