engine shaft mishap, my options?

Status
Not open for further replies.

Bluethunder3320

New member
Messages
5,677
Reaction score
39
Sweet, that looks cool man.

despite no muffler, governor, permanent tank, flywheel cover or shrouds, kill switch, throttle assembly, probably much more, all i was trying to prove is that i got it to RUN after a lot of work (it took like 4-5 months to accumulate enough parts)
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
ok here is the blown up tecumseh 9hp rod against the 8hp rod. notice the 9hp is alot beefier.



dont i have alot of engines? lol, and a briggs on my kart thing outside, another clone on my baja, a scooter engine, a leaf blower 2 stroke, 2 chainsaws, 2 weedwackers, and like 3 or 4 electric motors.

only took a year to collect!

 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
going clockwise,

8hp tecumseh (all apart)
greyhound clone (broken choke tab)
9hp tecumseh (blown up and some parts missing)
6hp tecumseh (missing some parts but i had it running)
13.5 briggs (had low comp, got new rings, but i dont have the e-start so i cant test it...)
greyhound clone, runs, brand new....

outside:
6hp briggs flathead (vertical shaft. runs good)
6.5 clone on my baja
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
Out of all my engines, the 13.5 i spent $10 on it, and i bought one of those clones for $100 new.

Every single other engine was free expet the 3rd clone thst came with my mini bike....
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
Good news, going to the machine shop saturday!

Also got the POR15 starter kit and its awesome! Just tried some maine clean on the carbon in the head and it literally MELTED off..... My skin feels a bit tight now.... LOL
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
And cam, ill see what this guy says first, who knows he may be like um... Cant do it... Because it would be hard to get perfect.

This guy does insanely precise work, like i said, last year when i met him he was in the middle of welding a engine head for a bonneville salt flats car.
 

Clayton

New member
Messages
294
Reaction score
0
Location
Saskatchewan, Canada
Yeah, I know how that is, i have about 3 or 4, 3hp briggs faltheads that can run, but I have messed up and don't have parts for. Sometimes you can do it yourself to a fault.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
All the engines in the pics are at dfferent stages of running.

For some i never had parts to begin with, and others like the 13.5hp just need time, i should have parts for it to run (i got it all apart)

I hope machining this shaft wont cost more than $70-80 TOPS.
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
If the machine shop guy just laughs at you and says he can't fix it because you tried to angle grind a motor pinned at WOT while metal is lathed at a few hundred RPM, I'd say you'd best bet it to hit youeslef in the head a few times wjth that shaft in hopes of straightening it and learning something. :p Anyways, good luck with the machine shop and I hope he cuts you a fair price.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
alright, well.............

i showed him a 1" briggs shaft, and i showed him a 3/4" H60 shaft. i basically said this is what it used to look like, then i grinded it, trying to get it to this.. and i ended up with this. how do i get back to 3/4? he said well he thinks its cool that i tried, but he says he just worked on a harley shaft and it was a PITA to build up and get back down. especially because that one didnt fit in a lathe.... long story short, he said its a lesson learned for sure, i gotta know my limitations, i cant do anything with a grinder and a running engine. i broke the news to him that tecumseh has been out of business for a couple years..... so i cant just go buy a cheap part.

well, he estimated $250-300ish just to get it back to 3/4". NOOOOO! he said if i got him a 1" shaft, so he doesnt have to build it up with welds just machine down, he said its ALOT easier and he would be able to do it for around $100..... so i might just buy a 1" TC.

also he said its a real PITA to do, weld and let cool, weld and let cool, mark, machine, repeat.......................


well on the bright side, i was looking on CL, and i found an ad for a not running tecumseh 8hp for $25!!!!!!!!

^^^^^^and guess what, they are within a MILE OF MY HOUSE! so im just gonna go knock on their door and hope that they still got it!!!!!
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
NOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO

he sold it already.

also last week his 5hp chipper wouldnt start so he threw it out. NOOOOOOOOOOOOO

but he did take my name and number in case he has any more crap to throw out.


and he reccomended me to a place nearby where a guy was selling a chipper. he wanted $125 for it.... i would offer $50. BUT i noticed the exhaust was cracked off the block.


so, ill post pics of the thing in a minute. oh and someone also took the tractor he had.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
trying again......

found a way to spin the engine slow.



straightened keyway a bit so i cold fit the clutch on.



smoothed out







this is the amount of play.

 
Status
Not open for further replies.
Top