Eating up belts

Status
Not open for further replies.

Lawes12

New member
Messages
18
Reaction score
0
My torque converter is eating up belts fast! I was wondering if a way too tight of a chain will cause this? Any other suggestions?
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
number one reason for excessive belt wear: bad gear ratio!

number two: misalignment
also..
low quality belts (cheaper is not always better ;))
dirt grime or rust on the sheaves
etc.etc.

But frankly.. if I had to make a guess.. it'd be number one.. bad gear ratio

'sid
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
So tell us your tooth counts and tire size (height) and we can determine Good or Bad Gear ratio.
 

Lawes12

New member
Messages
18
Reaction score
0
Fairly new build I have a 8 tooth driven sprocket and a 48 tooth axle sprocket so a 6:1 gear ratio with 20 inch tires on a two seater go cart with a knockoff tav 2 torque converter.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
there you go.. with 20" wheels on a two seater...
let me guess 6.5hp and ~650 lbs? (the spiderbox alone is ~400lbs!)

close? well then ~8.5:1 ratio is needed to move without burning belts

'sid
 

Lawes12

New member
Messages
18
Reaction score
0
Ok thanks again!

---------- Post added at 09:40 AM ---------- Previous post was at 09:37 AM ----------

If I were to go a ratio of 7.5:1 with smaller tires would that help or no? The problem with going bigger axle sprocket is finding one big enough and clearance issues.

---------- Post added at 09:48 AM ---------- Previous post was at 09:40 AM ----------

I also adjust the torque converter spring to the 3 rd hole for more torque good idea or no?

---------- Post added at 10:26 AM ---------- Previous post was at 09:48 AM ----------

No it is a 10 hp
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
I have ran both 6:1 and 7.5 :1 on my 2 seater with 16" tires. Not many hrs on either. Maybe 5 hrs each. Haven't had to switch original "Chinese" belt yet. I like the way buggy performs with 7.5 :1 and 16" tires. Modded Predator 212cc 6.5 HP original rating
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
[/COLOR]If I were to go a ratio of 7.5:1 with smaller tires would that help or no? The problem with going bigger axle sprocket is finding one big enough and clearance issues.

7.5:1 is good for 6.5hp on 18"

(engine mods do NOT count I'm afraid.. we talk about low rpm torque issues here!)
if you have a modded engine you most likely just added rpms (thus increasing the hp without increasing the torque)

if it's indeed a 10hp engine (i.e. at least an old GX270, a newer GX290 or a 300cc predator...)
then you should have enough torque to run 7.5:1 ratio on 20" wheels

'sid
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
Any thoughts????? I don't know enough to try to argue, lol, just asking???????
http://www.kartpartsdepot.com/product_p/001.htm

According to this article, stage 1 mods (jets, air filter, exhaust) done to a 6.5 HP 212cc Predator increased max torque to 14.10 ft*lb @ 2300 RPM (HF claims 8.1 ft*lb @ 2500) and close to 9 HP @ 3600 RPM (HF claims 6.5 HP @ 3600).

I understand dyno readings are "Corrected" and "Relative" so not sure how to take these numbers.

EXCERPT:
First, we need a baseline horsepower and torque number. That means a trip to see Dr. Dyno and “The Search for the Truth” begins. Before starting any process that involves change, it’s always good to have an idea of what you have to start with. And a dyno is as good as it gets for this. In order to meet EPA standards you will find these clones are jetted very lean. In fact, they are too lean for what we want. Usually, the clone’s main jet is #70. I have found that #85 - #90 works better at most elevations and should get you in the ballpark and on your way to making safe and reliable power.
The other jet of concern is the pilot jet. And that is located just under the idle screw adjuster. Normal pilot jets are in the range of .014”. We want .020” to richen up the
bottom end, and help with acceleration off idle, and through the low part of midrange just before the main jet takes over.
So off comes the gas tank to be replaced with an aluminum top plate for added strength. Then the air box and stock filter to be replaced by a K & N racing style air filter and adaptor. Next, let’s complete this motor’s breathing improvements and get rid of that very restrictive exhaust system and spark arrestor for an open pipe into Dr. Dyno’s exhaust analyzer sensors. Add some of your favorite oil and we are ready for our appointment with the good Dr.
Our Predator fired right up without hesitation and ran smooth for its 30 minute break in. The new jetting was much to her liking with smooth acceleration and crisp throttle response. Ungoverned, the Predator was very anxious to turn more rpm’s than the manufacture would like to hear about. After warming up to a head temp of 275˚ I laid the hammer down and let Dr. Dyno take over. The manufacturer stated 6.5 horsepower at 3600rpms. With the improvements we did our test results were closer to 9 horsepower at 3600rpm with maximum torque pulling 14.10 ft. lbs. at 2300rpms. The maximum horsepower of 9.83 was achieved at 4700rpms. Power started dropping off at 4900rpms and we hit a wall at 5600. I believe some valve float was limiting our revs after that.
 

FreeRunner15

=======
Messages
660
Reaction score
10
Location
================
Any thoughts????? I don't know enough to try to argue, lol, just asking???????
http://www.kartpartsdepot.com/product_p/001.htm

According to this article, stage 1 mods (jets, air filter, exhaust) done to a 6.5 HP 212cc Predator increased max torque to 14.10 ft*lb @ 2300 RPM (HF claims 8.1 ft*lb @ 2500) and close to 9 HP @ 3600 RPM (HF claims 6.5 HP @ 3600).

I understand dyno readings are "Corrected" and "Relative" so not sure how to take these numbers.

i personally was afraid to say anything because it's coming from me.

but when i put the torque converter on it laid torque down easier, but thats from the CVT and not the engine. So anyways:

When i messed with the fuel excessively and removed the air intake it would "throw" the torque converter into high gear much quicker and leave a 12.5 foot tire mark in the process with about 190 pounds on the kart.
i think, but not too sure, that the excess fuel intake and removed intake tests i've done Had enough power to damage the belt some.
After all it does have black a solid black mark on the driver clutch that possibly is proof of that theory with 4:1 ratio 15" tires. The CVT didn't do that before the fuel and intake upgrade.
Another vital thing i need to add.. the 4:1 ratio CVT didnt have as bad a black mark BEFORE the fuel/air modification also.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
Any thoughts????? I don't know enough to try to argue, lol, just asking???????
http://www.kartpartsdepot.com/product_p/001.htm

According to this article, stage 1 mods (jets, air filter, exhaust) done to a 6.5 HP 212cc Predator increased max torque to 14.10 ft*lb @ 2300 RPM (HF claims 8.1 ft*lb @ 2500) and close to 9 HP @ 3600 RPM (HF claims 6.5 HP @ 3600).

I can't see the units for torque on the screenshot...
might be a coincidence that the stock engine is producing 12Nm roughly, and that 14Nm seems to be a plausible result with no more than rejetting..
Anyways... cool if they managed to achieve 14 ft lbs if they did..
and if that's repeatable.. even better!

if you're burning belts on your go kart, and do not have a dyno handy to test the actual Torque at clutch engagement speed...
there are two possibilities:
1) you assume you have more torque than you actually have and gear higher, burn a belt (~$25) and regear (new sprocket, new chain... another 20 bucks)
2) you assume you have at least the stock torque, lose a mph on top speed and gear accordingly the first time.

In fact.. we were asked for an advice...
and as such the second option is the better advice ;)
(it WILL WORK plus you don't lose money trying)

we also advise people to wear helmets;
(and we all know that every now and then we don't wear helmets ourselves.. but that's not good advice, is it?)

And with that;
Lawes knows what to do, and got an idea what could be done which may or may not work out for him.
in the end, it's his choice anyways ;)

'sid
 

cavfire

Member
Messages
110
Reaction score
1
Location
auburn, georgia
If alignment is good and you're riding on hilly terrain you may be forced to re-gear, otherwise something as simple as rolling the throttle a little more and no jack rabbit starts could greatly increase belt life.
 
Status
Not open for further replies.
Top