Dies when no choke

Status
Not open for further replies.

allanbranch

newbie gokart builder
Messages
32
Reaction score
0
Honda 6hp XR2750

The engine dies when I lessen the choke. I know nothing about engines go easy on me.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
You need to clean your carburetor.....not enough fuel is getting to the combustion chamber. ... You can Google up cleaning a carb for your motor -if someone doesn't post a link first. .....
 

J_Walker

New member
Messages
898
Reaction score
2
Location
Florida
if the carb is clean, and your still experiencing this issue. check your float levels.

but make SURE your carb is clean first. no need messing with float levels when you don't got too!
 

allanbranch

newbie gokart builder
Messages
32
Reaction score
0
The carb, once it's running, drips gas from the overflow tube that runs from the bottom of the carb. When I cleaned the carb everything was really clean, no gunk anywhere, I could see thru all the holes too. I didn't touch the pilot screw, I'm trying that now.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Generally, the overflow drip is a sign that the fuel inlet valve (float, needle, and seat) is not sealing properly. Check that float is correctly set, that it operates, that the needle and seat are clean and undamaged. A simple test I like to do, is as follows:

Drain and dismount carb. Attach a length of clean hose to the fuel inlet nipple. Holding carb level, blow into the hose. You should be able to blow air right into the carb, and hear it escaping through the various nozzles and vents. Now, invert carb, and blow. No matter how hard you blow, you should NOT be able to get air into the carb. Flip, repeat, flip, repeat. I usually do it a few times to make sure float isn't hanging up on something.
 

The Icebox

New member
Messages
11
Reaction score
0
I too am having the same issue with a Honda GX270 (9hp) on my Manco. I read somewhere that head gaskets could possibly have the same effect of dying when the choke is off. Is this true?
 

The Icebox

New member
Messages
11
Reaction score
0
I took the carb off and put some rubber gasket sealer stuff that dries wherever you spread it and it seems to be working fine now. She purrrs pretty now thats all i need. Thank you!
 

solomon

Active member
Messages
1,648
Reaction score
8
Location
ca
Replace it with a real gasket. Most of that rtv sealant doesn't hold up well to fuel
 

ZR2Chevy22

New member
Messages
20
Reaction score
0
Location
Kemah, TX
Well I have a Briggs and Stratton 5hp Fun power engine and I have the same issue. I recently cleaned the carb and used a carb rebuild kit for a fixed jet pulsejet carb. Made sure everything was clean and clear, put new gaskets, pump blader and all. mine will idle fine with the choke about 1/4 of the way on.

What I'm thinking is that I need to adjust the air/fuel mixture. I bottomed it out then went 1 1/2 turns out like suggested. I'm thinking it needs alittle more. What ya'll think?

Andrew
 

88nightrider

New member
Messages
130
Reaction score
4
Location
Norway, Sandnessjoen
What I'm thinking is that I need to adjust the air/fuel mixture. I bottomed it out then went 1 1/2 turns out like suggested. I'm thinking it needs alittle more. What ya'll think?

Andrew
Normally I use (on cars, bikes, chainsaws +++. Most things really) 2,5 turns out as a starting point

Edit: And be really careful when "bottoming out" the mixture needle. If you do it too hard, you may damage either the seat or the needle
 

solomon

Active member
Messages
1,648
Reaction score
8
Location
ca
Did you replace the tank to carb gasket and caeb to intake gasket? Also did u clean the tank? Iirc those tanks get garbage built up near the top where the carb bolts down and causes issues. Good luck. I've had some carbs that were do old and tired that they never adjusted well enough to run them on a kart
 

ZR2Chevy22

New member
Messages
20
Reaction score
0
Location
Kemah, TX
Solomon, I cleaned the entire tank and all mating surfaces I used new gaskets all around.

88, I know not to bottom them out to hard. I screwed it down just till it touched then backed it out the 1.5 turns. I will go another half and see if that lets it idle with the choke off. If not I'll go another half to 2.5 turns out and see.

Thanks for the help thus far.

Andrew
 

ZR2Chevy22

New member
Messages
20
Reaction score
0
Location
Kemah, TX
How far is you idle screw backed out?

I screwed it out 1.5 turns when I rebuilt the carb like I read in a writeup on the pulsejet carb rebuild. I screwed it out to 2 turns today and it will now idle with the choke off. The slowly started closing it until it sputtered from to little fuel then went up about an 1/8th of a turn so it's actually more like 1.75.
 

solomon

Active member
Messages
1,648
Reaction score
8
Location
ca
If ur idling without choke on do a plug chop and see where your air/fuel mixture is at
 
Status
Not open for further replies.
Top