Converting from recoil to electric start

Status
Not open for further replies.

OBXFAN

New member
Messages
5
Reaction score
0
I have a Manco Go-Kart with a 5 hp Tecumseh OHH50 recoil engine. Mounting bolt pattern is 3-1/8 by 6-3/8 (OC's). I want to replace this engine with an electric start engine, such as a 7 HP Duromax, to make it easier on my young grandsons to use the kart. I've learned the Duromax bolt pattern is 3-3/4 by 7-3/4 (OC's).

Here are a few initial questions I have:

1. I have enough metal on the existing mounting mounting plate to redrill new holes to accept a new engine, but I was wondering if there are any other electric start engines with same bolt pattern as the OHH50. My searches all come up with Durmax engines. Does anyone have any recos? Are there any off the shelf adapters I could purchase to connect a Duromax to the existing mounting plate?

2. Do these electric start engines require an external battery? There is very little technical information on the internet about these engines.

3. The OHH50 has a 3/4 shaft. Are key way widths standard? That is, does every 3/4 engine have the same key width? If not, are there clutches made for the different widths?

Thanks everyone
Bob
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
1. Most, if not all, 5-7hp engines have the same or very similar bolt pattern; redrilling should not be required...

2. Only if you want to use the electric start...

3. All 3/4" shafts have a 3/16" keyway, 1" will have a 1/4" keyway, 1 1/4" will have a 5/16" keyway & so on; I'm not just referring to engine PTO shafts, shafts in general have keyways cut to those dimensions...
 

OBXFAN

New member
Messages
5
Reaction score
0
Converting recoil to electric start

Thank you gentlemen. We (Tommy-15 yrs old, Matthew - 12, Nicky -9, and even Cross- 5, and Jacob -3) REALLY appreciate the sonic replies.

Bob (67)

:welcome2:
 

afremont

New member
Messages
148
Reaction score
1
Location
houston
Are there any of the old wind-up starters left in the world? I haven't seen one since the late 60's. Anyone besides me old enough to remember them? Briggs had them mostly, but so did Tecumseh and Clinton I believe.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Are there any of the old wind-up starters left in the world? I haven't seen one since the late 60's. Anyone besides me old enough to remember them? Briggs had them mostly, but so did Tecumseh and Clinton I believe.

I do...vaugely...IIRC....The one I had , had a handle with a knob ....and you flipped the handle over to open it...cranked it....and when you pushed the handle back down on the engine it released the spring...

It's so far back that it's fuzzy....but IIRC....it took quite a few turns to operate...

No wonder the pull recoil starter sent it the way of the dinosaurs.
 

afremont

New member
Messages
148
Reaction score
1
Location
houston
You only had to crank them about 5 times around and they never broke. I think planned obsolescence is what sent them into oblivion. There's some youtube videos showing some that are 50 years old and still working. How many 50 year old ropes do see out there? ;)

Then there was the wind the rope around the cup and pull hoping that it would detach when the motor started. I know why those went away, lawyers.....
 
Status
Not open for further replies.
Top