compression and rpm capability

Status
Not open for further replies.

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
Hey guys got my motor partially assmebled back rain just won't hold off. here's the setup 6.5 clone (greyhound blue HF) ARC billet flywheel and billet rod 0.020" longer than stock honda flat top piston. 0.050" offset timing key approx. 8 degrees advance 91.5 main jet pilot jet drilled with #72 bit K&N filter and billet adapter custom header 18lbs. springs, no governor. What would be the best timing key for this setup, I hear 1 degree off can hurt performance.Recently my stock rod shattered so now I'm wondering what are the expected rpms on this setup. Looking at pvl coil w/rev limiter and was wondering what the max rpm I could limit the engine without any damage. Is it possible to buy the coil without buying the kit. If not anyone know of another cheap way to limit rpm at a safe level. Anyone can shed some knowledge on this that would be appreciated. Also wondering if anyone knows what the compression ratio would be with the 0.020 longer rod and flat top piston. Thanks guys
 

slideways

New member
Messages
575
Reaction score
6
I wouldn't turn it over 7000 myself. The 18lb springs will limit rpms slightly. 26lb will be the unlimited rpm ones but they will hurt a cam not meant for them.

You don't have any hot cam in this? I would only run about 4deg advance. You are just going to be making noise anyway without a cam and carb work meant to handle it.
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
hey guys got my motor back running its fast but not for long its hard to start still. You gotta have the gas pressed to start and after a few trips down the road with the kids it start sputtering and come alive and dies until it cuts off. I feel like its overheating. I pulled the spark plug it is smut black on the outside rim the porcelain around the electrode is a tan white color. it still won't crank with the choke closed at all. It doesnt wanna idle well at all. I ordered the 4 degree offset timing key. it won't be here til monday. I was gonna order a stock class cheater cam but want to get it right first. Any ideas anyone?
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Are you running the stock carb? With all the upgrades you've done the carb may not be able to keep up. One thing I learned a long time ago was "the better an engine can breathe the better it will run". Upgrading the internals will only be truly successful if the intake/exhaust can handle it.

It sounds to me like this is what is happening; the engine wants to go but the carby can't feed it quick enough. On the other hand, it may simply be a leaky gasket or miture setting is off.
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
yes I'm running the stock carb with k&n filter 91.5 main jet gx160 emulsion tube and drilled the pilot jet with a #72 drill bit. All the upgrades I'm able to do myself I was gonna see if a small engine shop nearby would bore the carb for me but he said he needs to see it first and I need to get him some specs on the ones I looked at online and see what they were bored. I seen alot saying .625 bore. I seen one I like said .750 throttle bore and approx .680 venturi. Hopefully he'l give me a good estimate Monday. Or I was gonna buy one what should I upgrade first I was looking at a cheater clone cam saying will work with stock carb, or should I get the carb first and get a cam next?
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Logic would dictate that you get it running before you attempt to get it to run better don't you think?

Get your carb sorted first
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
the first sentence of my 2nd post says motor running and then goes on to say what its doing as to why I need it running better. I found a crack in the fuel line today it was dripping on the chainguard took the carb off and cleaned it got new fuel line and filter. it didnt die out while running it today. adjusted the idle screw more it cranks easier now. idle is almost at the torque converter engaging to crank easy. Still will not crank with the choke closed. choke kills it.
 

Davidgx200

New member
Messages
54
Reaction score
0
Location
Aiken South Carolina
put the 4 degree timing key in and all is well again easy 1st pull start up and idle even used the choke to crank it up. seems to have a little more throttle response. Thanks slideways for the timing tip.
 

slideways

New member
Messages
575
Reaction score
6
No problem... just FYI alot of guys that work the carbs on the clones can't start them without a touch of the throttle either. My barstool won't fire until i just touch the throttle open a tad. Its a stock motor with intake/exhaust no governor but has the jets drilled to make it run correctly.
 
Status
Not open for further replies.
Top