Comet 40 on a 6.5?

Status
Not open for further replies.

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
So... Here's the situation. I'm getting very close to yanking the GX340 off of my kart, and stuffing in the XV250 twin that I had planned for another project. I'll probably sell the GX to recoup some funds.

What that leaves me with, is a perfectly functional Comet 40 set to potentially use on my upcoming 6.5 clone-powered project.

I can adapt the shaft size, that's not a problem. Here's the problem- according to Comet's specs, the minimum hp rating for the 40 is 8hp. I would be using a very lightly modded 6.5. Can anyone foresee any potential problems/solutions?

Cheers! Chris
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
could it just say that so people buy a 30 or 20 series for a smaller engine? only problems i can think of are:
more weight to get spinning?
requires more power to move the larger belt (i don't think thats a problem).
driven springs tighter?


i don't see why you can't just throw it on there and try it out! (i guess you would need a js setup.)
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
I think Comet just claimed 8hp as the minimum because that's typically the lowest hp engines that have 1" cranks. Besides as long as you were using a good race header, air filter, re-jetted and set your valve lash down to .03 and yanked the governor you'd probably be pushing around 8hp with your 6.5 clone anyway.
(check the dyno readings half way down this page: http://arcracing.blogspot.com/searc...-max=2009-01-01T00:00:00-05:00&max-results=27
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
I was thinking many of these thoughts myself. I was fairly happy thinking that Comet's minimum 8hp rating was based entirely on the fact that 1" shafts don't tend to appear on engines smaller than 8hp.

Then, my mind got carried away. I started wondering if 6.5hp was going to create problems with the driver not closing properly, or some kind of spring tension issue.

The more I think about it, the less I think it will be a problem. RPM is RPM. And the driver is, well, RPM actuated. So unless the the driver has a massive rotating mass (which it doesn't), the 6.5 should have no less trouble spinning it up than an 8hp engine, no?

Does that seem to make sense to you guys?
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
Well, it can't hurt to adapt the motor to it with PTO shims, much like I did, to find it won't work where you can then sell the 40 series to completely cover the cost of a 30 series and then some. But I agree, I see no reason why it won't work. The cent. force is the same at XXXX RPM's due to the weight pack, not the PTO. I think it would be fine.
 

pinoyclass

New member
Messages
10
Reaction score
0
I am in need of a comet 40 series! I am willing to purchase it off of you so you can have some money to get the proper comet 30 series you need! The 40's are hard to find but the 30s seem to be a lot easier to find! Let me know what you think I am willing to pay $175 if you can ship it to Florida.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Yeah- Don't anybody take this the wrong way, It's not meant to be mean, but

With Comet out of business and good CVT's a bit tough to find
The very good running condition of my 40
And the state of the market around me

there's no way I'd ship this off for $175.

Sorry. That's just how things look from here.

EDIT- I just looked at your links, Redsox- Does MFG actually have stock? I didn't see anything that said no...
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
I have a 40 series on my 6.5 and it works great! You will have to make/ get a jackshaft kit, and you can get a piece of 3/4" I/d and 1" external diameter tube, and cut some keyways in it, and put it on the shaft.
Rob
 

metalthrashinman

New member
Messages
279
Reaction score
0
Location
Hope, NJ
Comet 40's are tough to come by these days. One just sold on ebay. I was going to bid, but I have a trusted source for one that I am calling this week. GTC is such a bunch of liars that I am still foaming at the mouth over the wasted time and money they have costed me. Hindsight is always 20/20.

http://cgi.ebay.com/ebaymotors/ws/e...0646064131&viewitem=&sspagename=STRK:MEWAX:IT

I called Northern, and they have none. Left me feeling like they were ready to take my money for something they don't have. The salesman got all weird when he figured out that I really did know what I was talking about.

Be careful out there guys, they're always ready to take your hard earned $!

As for the 40 working with a lower hp motor, I see no problem. As you said, rpm is rpm; right? Geared properly, that is...
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
Has anyone talked to MFG about whether or not they have them in stock? I get this terrible feeling that there is a semi trailer wrecked in a ditch somewhere filled with thousands of Comet TC's that will be uncovered in about 10 years, all in pristine condition and sold on Ebay for a killing.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Has anyone talked to MFG about whether or not they have them in stock? I get this terrible feeling that there is a semi trailer wrecked in a ditch somewhere filled with thousands of Comet TC's that will be uncovered in about 10 years, all in pristine condition and sold on Ebay for a killing.

I wouldn't doubt it. I'm worried enough about replacement belts.

A guy called me from CVTech today. I was at work and didn't have much time to talk, but he fixed me up with a phone number for their distributing division. He did make it fairly clear to me that their stuff is aimed at higher HP apps, specifically saying 1" shafts and up. He told me for 5/8" and 3/4" I was best to check out MaxTorque. I dunno- MaxTorque has done some OEM stuff, but retail?

Anyhow, I'll give them a call in the next few days and see what info I can get. Maybe I'll even post the number up here, but I've left it in my truck...

Pinoyclass, I'm sorry to disappoint you, but it's not going to happen. Nothing against you, I like your money as much as I like anybody's. But I want to use my 40 if I can because
1)I already own it
2)I don't want to have to track down a used 30 or TAV in unknown condition, and probably pay too much for it, to boot 3)I'm wary of GTC and am definitely not throwing any money at the chinese-what is it- Jongshingbangdong thing, not without more reviews
4)I'm in Canada, shipping is not something I'm willing to pay
5)If I can't use it, I have a local friend that has an interesting project concept that would require it, and I would get what I'd want for it
6)I'm a horrible pack rat, and I will likely hold onto it until I die (see "Last Will And Testament of Toystory_4wd"

Either way, when the project gets closer to materializing, I will work on fitment.

Cheers, all!

Oh- AND I would actually prefer to have the driven on a seperate jackshaft for this project-don't ask...
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
I'm in the same boat there about the JS. My TC backplate only fit facing forward and forcing the seat up because the bearing house would with any other arrangement, except vertical down, but the motor mount was already built.
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
We've had issues with series 30 engaging on 5.5hp engines without changing the ratio for full engagement, you may have similar issues with a smaller engine on the 40, it simply might not have the torque to compensate.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Thanks for weighing in. I'm assuming you refer to a spring/weight change? When I reach that point if I have such an issue, I will post the details.

Since we're here, what is the "minimum hp" for the 30, and how was the problem dealt with?
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
BMI Karts actually has Comet 40 belts on clearance so, maybe buy up a stock of those and then build your JS around the suggested CD of those belts.
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
i'm 99 percent sure gokartsupply.com is selling GTC 40 series, wouldn't be horribly surprised if mfg was doing the same.

if the 40 series driven has a higher tension spring it may take more force to open.

once spring hits i should be able to finally get in a a few hours on my kart and give a review on the gtc tc2. so far, no complaints. well there is one thing, but i don't think it has to do with the tc itself, i'm running #40 on a #41 sprocket (as suggested to me several times) and it seams the chain flexes over to the side and has eaten of anodized layer of aluminum on the back plate.
 
Status
Not open for further replies.
Top