NotSoMasterMind
New member
sorry, it is on the left side. but i dont need a jackshaft overall anyways
sorry, it is on the left side. but i dont need a jackshaft overall anyways
sorry, it on the left sideThis is very disturbing, RIGHT SIDE ?
here are some picsNO....the main point of why jackshaft is being repeated... It allows compound gearing.....
and other options....
My bike has a large rear tire.. A spare car tire. This has a large 24" OD. Now aside of a few engineering details(the right side drive), I needed the jackshaft to modify the gearing from just having a chain to the clutch to the rear tire.
In you kart. you have a tall rear tire, and a burning clutch. adding a jackshaft to modify the gearing set to accommodate those elements, to reduce strain on the clutch.
Off hand..... some numbers I just through out there...
14-24-14-60 =7.347:1...... thats a start...
Heres the ratio calc...
http://www.affordablegokarts.com/GearCalc.php
We also need some pic on what were dealing with?
i want help, just a jackshaft is too hard for someone who can't weld, and is 13, this is also my 1st go kart... And I'm limited on space to put stuffWhy do you say you dont need a jackshaft ?
Did you want help with your problem or not ?
they are 17 inch tires.... would it really be that hard to turn it, causing it to get hot? or can i get something to cool it down?Well then you need smaller tires for the ratio to work
they are 17 inch tires.... would it really be that hard to turn it, causing it to get hot? or can i get something to cool it down?
at most i can move my engine 1/2 inches, the engine hardly fits on the mounting plateJust drive it underwater....REALLY? Dude! This is not that complicated..... just listen up...and do what we say....
You want to put a radiator on a clutch...instead of properly gearing your kart....you want to add a chain tensioner...instead of simply slotting your engine plate..(or replacing it with the proper one off the net.)
Jeesh....
and i have a 1inch bore, $60 for the cheapest clutch i can find.Keeping it cool is NOT the issue, Heat is the result of the clutch Slipping. The slipping is the problem that will destroy the clutch. The heat is just the product of it slipping..
All you need to do is buy a 10 tooth clutch. 20 bucks on ebay.
Although your tires are still oversized for the 6:1 ratio of a 10 tooth. You will be alot better off, and 20 bucks make it worth a try.
thanks, the best anwser i got all day... thanks for the info, i might just go with thisRight......so....you are going to destroy a high dollar 1" bore clutch because you simply cannot seem to grasp that you MUST change your gearing.
Or that the purpose of a jackshaft is not to change where the sprockets are..but to allow a smaller axle sprocket to achieve a higher gearing..(something you desperately need).
Now.....you can probably run a 90 something tooth sprocket...without ground clearance issues if it mounts to the wheel....and this is only going to set you back $20 or $30....sooooo.....maybe you don't need a jackshaft, but......you DEFINITELY need higher gearing.
And....again...I don't give a hoot how tight it is (in your mind) to "fit" this engine. Simply slotting your engine plate and choosing the right amount and kind of links is the cheapest, easiest. way to solve your loose chain issue.....
We can't help you if you don't listen.
thanks so much!!!you can get somthin like this and not have to weld anything and be able to adjust your chain. http://www.minichopperssocal.com/JACKSHAFT-SYSTEM.html
i have a place, but i might just get a bigger sprocket, or save up for a bolt on jackshaft.. its only $90 compared to a $105 sprocketMaybe you can find a smaller sprocket for your clutch. again maybe 20 bucks
you can get somthin like this and not have to weld anything and be able to adjust your chain. http://www.minichopperssocal.com/JACKSHAFT-SYSTEM.html
Here is a selection of sprockets for your clutch....
like Chancer said... about ~$20....
http://www.bmikarts.com/Replacement-Parts_c_219.html