Carter mini monster project

Status
Not open for further replies.

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
Hi guys, I got the 16hp vanguard bolted up in my Carter mini monster. It's a tight fit but it will work. Now I'm working on the jackshaft setup for the secondary clutch. I've got a plan that should work good. I did not like the original setup. It was for I believe a 5hp engine. Seemed very light duty to me. The shaft is only supported from one side. since I'm going to a 16hp engine and I'm rather heavy I want to beef this up. I'm thinking a pillow block(think that's what they're called) on each side of the jackshaft and locate the keyed secondary where I need it on the shaft with lock collars. So I'll need a longer jackshaft and one that has a keyway the full length. Does anyone know if these shafts have a keyway the full length. It's a tad long but I can work with it. I didn't see it in the description and I can't visually see it in the pics. Or where I could get the correct one?

http://www.mfgsupply.com/gomini/gominiaxles/gominijackshaft/gominijackshaftonly/az8183-10.html

This is my first go kart so I'm not familiar with this stuff at all. If my idea could be improved on or you know of a better idea I'd like to hear it. Thanks!
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Sounds to me like you have it sorted, that's exactly what I'd do.

If you're fighting for space, another option is a hollow tube welded to the frame with roller bearings between it & the jackshaft (see pics below), then mount the clutch/sprocket on the ends. A spacer will be needed to keep the bearings apart but the clutch/sprocket will act as end stops. The downside to this idea is you can't "side load" rollers (like front wheel bearings) so you will end up with a small amount of side movement, but not enough to cause a problem

That's one thing I don't like about MFG; descriptions are not very descriptive... & the pics have no zoom ability. However, the shaft in question appears (to me anyway) to have a full length keyway; you should be good to go
 

Attachments

  • SDC10271.jpg
    SDC10271.jpg
    64.7 KB · Views: 1
  • SDC10272.jpg
    SDC10272.jpg
    63.6 KB · Views: 0
  • SDC10273.jpg
    SDC10273.jpg
    66.2 KB · Views: 0

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
I went ahead and ordered that one. The prices are great on the this stuff. Im used to getting charged out the wazoo for Odyssey parts. I might order a tie rod kit from them as well. Have to measure after work.
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
Can you really run needle bearings over key-way on a shaft? It seems like it would cause some problems. At the very least I would file down a key so that it is flush with the shafts OD when installed, that way the needle bearing has something to ride on. Ideally needle bearings should be on hardened shafts, or on a hardened sleeve pressed over the shaft. If you are dead set on using needle bearings I would also suggest some thrust washers to take any possible side loads.

One more thing, it sounds like Fatcat is using a 16hp with a 40/44 series CVT. If that is the case the driven pulley should be supported by bearings on both sides. How limited is your space? If they can fit, I think ball bearings would be better (mounted in a flange, pillow block, or hollow tube).
 

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
Can you really run needle bearings over key-way on a shaft? It seems like it would cause some problems. At the very least I would file down a key so that it is flush with the shafts OD when installed, that way the needle bearing has something to ride on. Ideally needle bearings should be on hardened shafts, or on a hardened sleeve pressed over the shaft. If you are dead set on using needle bearings I would also suggest some thrust washers to take any possible side loads.

One more thing, it sounds like Fatcat is using a 16hp with a 40/44 series CVT. If that is the case the driven pulley should be supported by bearings on both sides. How limited is your space? If they can fit, I think ball bearings would be better (mounted in a flange, pillow block, or hollow tube).

Thanks for the tip on the key. I'll dwfinately use ball bearings. I do plan on supporting both sides. The single side is what I'm getting away from. Yes in using a 16hp vanguard with a comet 40 series clutch setup. It's cramped for room but I can do it. My only limiting factor is wanting to keep it inside the body. Thanks again.
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Can you really run needle bearings over key-way on a shaft? It seems like it would cause some problems. At the very least I would file down a key so that it is flush with the shafts OD when installed, that way the needle bearing has something to ride on. Ideally needle bearings should be on hardened shafts, or on a hardened sleeve pressed over the shaft. If you are dead set on using needle bearings I would also suggest some thrust washers to take any possible side loads.

One more thing, it sounds like Fatcat is using a 16hp with a 40/44 series CVT. If that is the case the driven pulley should be supported by bearings on both sides. How limited is your space? If they can fit, I think ball bearings would be better (mounted in a flange, pillow block, or hollow tube).

Good point, you're probably right, the keyway may damage the rollers. However, if the keyway was only cut into the end of the shaft it would be ok.

If the edge was filed off the keyway (as in round the edges) where it contacts the bearings this would also be ok.

The bottom line is it was a suggestion as requested by the OP; I never said it was a perfect solution :)
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
Is there ever a perfect solution?:confused: I think your idea is an excellent one for someone looking to keep things as compact as possible. I just wanted to make sure that Fatcat would avoid any possible problem I could foresee :thumbsup:.
 

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
Good point, you're probably right, the keyway may damage the rollers. However, if the keyway was only cut into the end of the shaft it would be ok.

If the edge was filed off the keyway (as in round the edges) where it contacts the bearings this would also be ok.

The bottom line is it was a suggestion as requested by the OP; I never said it was a perfect solution :)


I appreciate all the ideas. I'll take all of those and try to make it the best possible.
 

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
Picked up another fiberglass body tonight. Its a chevy stepside. Appears to be slightly smaller than the Carter but will be a good addition to my fleet. It's in pretty good shape but will need everything. It's just the body.
 
Status
Not open for further replies.
Top