carb cleaning ?

Status
Not open for further replies.

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
i pulled the carbs off my cm250 engine today so i can rejet it and clean it

i was wondering if i could use CRC instead of carb cleaner as i have non and if i get some it will only be used once so not worth it

i decided to pull them apart just so i could see how they work

i noticed people say to use a peice of wire from a wire brush to poke the jets out but mine were almost 2mm wide

so is this standard or does it mean i dont need to rejet it
 

sexyvicta

New member
Messages
806
Reaction score
2
im always cleaning lawnmower/weedeater carbs. CRC is inferior to carb cleaner i can tell you that. Carb cleaner is fully worth the $ aye. Degreaser in a can works ok for geting all the dirt out if you dont have carb cleaner. Or just use a tub of petrol
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
Do they sell CRC carb cleaner in Oz?

 

bighead

New member
Messages
4,022
Reaction score
54
Location
Pacific Northwest USA
I boil all my carbs in lemon juice. Nothing is better for cleaning carbs. Not even soak type carb cleaners. The lemon juice acid will get any and all crap out of the carb. You must spray with wd-40 or the like after you remove from the juice. Or the carb will oxidide really bad. I will stand behind lemon juice as I do POR15. Works more than great. And only takes about 20 minutes.




From this site. http://cycles.evanfell.com/2008/09/how-to-clean-a-motorcycle-carburetor-the-right-way/


Cleaning the Carb Bodies

Use the same squirt and wipe method noted above. Most of the time the other pressed jets and passages in the carburetors won’t be clogged. But if the bike has been sitting a real long time with squirrels in the airbox it is certainly possible. Us a compressor to blow some air into every passage you can see. Listen for the air coming out the other side. If no air compressor is available use a can of WD-40 with a straw attachment.


•Carb Dip – Most autoparts stores sell carb dip. It comes in a can similar to a paint can and is a VERY harsh cleaning agent. Soak the entire carbs in this dip. This dip can eat at rubber and plastics if they are submerged for too long, so try and remove everything you can from the carb bodies before soaking them. Once you pull them out swish the carbs around in a bucket of water to clean off the excess dip, then hose them down with WD-40 to get rid of the water.
•Boiling in Water – Not many people do this but it is by far the best way of cleaning carburetors. Dropping the carbs into a pot of boiling water will instantly free up stuck slides, throttle plates, and other frozen parts. It will also loosen the dirt and grime clogging up pressed jets and other passages. Just make sure to dry the carbs thoroughly with compressed air or the sun afterwards.
•Boiling in Lemon Juice – There is NOTHING BETTER at cleaning carbs than a giant pot of boiling lemon juice. The acidity from the lemons eats through everything; gas varnish, oil build up, dirt, grime, etc. Sometimes I won’t even bother doing anything but this – I’ll just remove the bowls, remove the caps, then drop everything into the pot and let it sit for 20 minutes (rotate them a few times). The one caveat to doing this is that you’ll want to wash the lemon juice off the carbs as soon as you pull them out. So have a bucket of water ready, or a can of WD-40 to hose them down. Also note that the acidity has a tendency to put a dull finish on the aluminum bodies of the carbs. This isn’t a problem in most cases, but if you must have everything shiny be prepared to do a little scrubbing and polishing afterwards. It may sound weird, but trust me, I just saved you LOTS of time. (Most dollar stores sell 1/2 gallon jugs of lemon juice, so buying a few gallons will only cost you $6. Plus you can put it back into the bottles afterwards and save it for next time.)


---------------------------------------------------------------------------

If you can’t see through the jet it is clogged and needs to be cleaned. Always try the easiest things first. Here’s an ordered list of a few things you can do to clean the jet.


•Blow through it. – Rarely works, but hey, who knows.
•Compressed air. – Force 100 pounds into it. Works occassionally. Make sure to hold the jet tightly so it doesn’t go flying across the garage. You might put the jet back into the carb body to hold it in place for this.
•Soak it in cleaner. – When I first started cleaning carbs I thought carb cleaner would be the magic answer. It isn’t. In fact, I hardly ever use carb cleaner any more, because it simply doesn’t do a very good job of anything but removing varnish from the bowl and slide. But try this.
•Poking it through. – Collect a few different diameters of needle like objects. A wire from a steel bristle brush works well, a bristle from a broom works well, a baby pin, small sewing needle, etc. Very gently try to poke it through the jet. If you are using a metal needle use caution, brass jets can scratch and deform easily.
•Boiling! – This works better than anything. Toss the jets into a pot of boiling water and let them bounce around for a couple minutes. When you pull them out blow some compressed air through them and you’ll most likely be good to go.
Some idle jets can be real tricky and never seem like they’ll be cleaned out . . . Just keep working at it, I’ve never met a jet that couldn’t be cleaned.
 

Rustydog2010

NZ Nutta :|
Messages
945
Reaction score
2
Location
New Zealand
CRC will be fine.

1) Disassemble.
2) Spray with CRC.
3) Blow all the passages out with compressed air.
4) Reassemble.

Done.

Jeremy.
 

CriticalMass

New member
Messages
239
Reaction score
1
Location
East Bay CA
No idea about jet sizes, but cleaning them is easy with a torch tip cleaner. Many different guages of scrapers and its a breeze, instead of trying to find needles or wires.

 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
ok crc it is

ok next question

how do u tell when the jet size is right as i will have to drill them out my self

You have to take spark plug readings to determine if you need to change the carbs jetting or not. This chart shows pics of what spark plugs would look like with overly lean/rich or perfect jetting.
http://www.dansmc.com/spark_plugs/spark_plugs_catalog.html

It'd probably be best to just leave your carbs stock jets as-is for now, Install some new spark plugs and see how they look after you've rode your kart for awhile. If you've modified your engines original exhaust system/air cleaner type, that'll probably change your jetting needs a little but you wouldn't be getting an accurate plug reading until you've rode your kart around at high RPM for awhile.
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
thanks for that

thats a good site iv added it in my favourites

i need new spark plugs as one is cracked down one side but still works

im going to perth this week (big city)

i think ill get my self a tacho and a set of 8 spark plugs
 

sexyvicta

New member
Messages
806
Reaction score
2
ok crc it is

honestly man the difference between normal crc and crc carb cleaner is night and day. Crc wont do anything. I use it to blow jets out etc if i have nothing else handy but any aerosol would work ok for that. The carb cleaner is like a super degreaser it just washes every thing super clean

buy a can of carb cleaner its not that expensive
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
:iagree:


Yeah. that's the reason I posted the pic of CRC carb cleaner up there. CRC makes a bunch of different different products, but they're Clean R Carb would work best on carbs!

Or some other brand of carb cleaner would be preferable to CRC electronic spray cleaner or whatever.
 
Status
Not open for further replies.
Top