Briggs Flathead Broken Oil Dipper

Status
Not open for further replies.

Arnie

New member
Messages
15
Reaction score
0
Location
Upstate/Central New York
Well guys I am new to the page and would firstly like to introduce myself :cornut: my names josh and I've been messing with engines and stuff for quite a while now and have a pretty good base of mechanical knowledge.

But anyway I am building up a Path Winder kart I picked up for a couple hundred bucks after I went to this clandestine track and raced one of their "loaner" karts and I immediately fell in love with it. the place/karts are nothing fancy, a pretty crude sandy clay oval in the backyard of a greenhouse here in upstate NY. They run 5hp flat heads, but allow modifications to the engine EXCEPT the carb, which somewhat regulates everyone to stay competitive. The karts are One-Wheel-Drive, using the left wheel only, and they run the track COUNTER CLOCKWISE! gotta say it was tough getting used to turning the "wrong" way for the first few laps.

But to get to my point, I popped the side off the case last night on my Briggs I/C to remove my governor, and found a nice chunk of the end of the oil dipper sitting in the bottom of the case :censored:. I can see some light scratches on the cylinder wall toward the very bottom, but the engine still runs great.
So my question is, do you think it would be alright to finish the season on this engine with just a new oil dipper installed? probably wont be more than 2 or 3 more races and I plan to do full teardown/build up of the internals this winter. If not, the kart has a 5hp Tecumseh endure OHV on it that runs well, but doesn't have much low end torque and once you run it in high rpms making a few passes, it seems like the needle valve can't full the bowl fast enough and she starves for fuel. let off it for a second to let the bowl fill, and it revs back up to normal.

Any tips on things I should do for the kart appreciated as well. Right now it's set up as a live rear axle, but the right rear is just on a bearing and free-spins. Most guys at the track just weld a 3/4x6 Grade 8 bolt on for their left rear axle and just run straight off that however I'd like to be able to switch back to 2wd in the off-season. MY kart is the green one, The black on is a kart that has run at the track for quite a while. I have a taller front left tire I just need to find some slick(ish) rears and she will be ready for race day:auto:
 

Attachments

  • 20151008_194253.jpg
    20151008_194253.jpg
    200.7 KB · Views: 14
  • 20151008_181736.jpg
    20151008_181736.jpg
    322.3 KB · Views: 17
  • 20151008_063009.jpg
    20151008_063009.jpg
    257 KB · Views: 14
  • 20151007_211555.jpg
    20151007_211555.jpg
    265.5 KB · Views: 17
  • 20151007_211543.jpg
    20151007_211543.jpg
    237.2 KB · Views: 18

Arnie

New member
Messages
15
Reaction score
0
Location
Upstate/Central New York
Yeah I'm in the process of doing that now but nobody I've called has had one yet. I have another old Briggs 4hp that doesn't run atm I could probably steal one from. Part of the old dipper is still there and apparently works a little bit because it hasn't blown up yet and the engine is from '93 lol! still better safe than sorry turning higher rpms. Thanks!
 

porsche930dude

New member
Messages
906
Reaction score
29
Location
Upstate, NY
That looks like fun wish i lived closer . im down in the binghamton area. iv made dippers before but its definatly better to find a real one. with a homemade one you never know if its going to break off or something.
 

Arnie

New member
Messages
15
Reaction score
0
Location
Upstate/Central New York
Well, my new ARC billet rod is on its way, that way I can at least get her running/moving for now. Probably gonna wait until next season to install a new dyno 94-SS cam and 1.485 20lb valve springs, and new valves for proper lash. as for now though, the governor is removed and the new rod will be here Monday. Am I safe running the old/stock piston? guy I know who build quite a few of these usually re-uses the psiton or gets a raptor 3 piston but he says they blow-by a bit more and burn oil which I'm not really a fan of.

So for now I plan on re-using stock piston, possibly with just new rings if I can find somewhere locally that has them in stock, if not I will be re using the old and hoping for the best. probably won't have much more use left this year before the snow falls so I'm running with it and keeping fingers crossed for now! more pics of the build to come. I've also decided to keep it Live-axle. Finding correct hubs/wheels/sprocket hubs that will all play nice with each other has been a HUGE pita, and I would have to grind off/move the engine mount plate, and alter the frame to get the clutch to clear. more trouble than it's worth if you ask me...it does 1-wheel drive fine the way it is and that's the way it's designed to be
 

Arnie

New member
Messages
15
Reaction score
0
Location
Upstate/Central New York
Here is the new paint scheme :2guns: kind of a "Loud" color but I like the brighter colors. Good news is the weather is gonna be crap all weekend so that should make waiting for my rod a little less annoying lol. Even the "s" word is in the forecast for tomorrow night :x
 

Attachments

  • 20151013_092625.jpg
    20151013_092625.jpg
    221.7 KB · Views: 4
  • 20151013_171054.jpg
    20151013_171054.jpg
    262.6 KB · Views: 7
  • 20151015_192514.jpg
    20151015_192514.jpg
    202.3 KB · Views: 3
  • 20151015_192528.jpg
    20151015_192528.jpg
    200.7 KB · Views: 3
Status
Not open for further replies.
Top