Arnie
New member
Well guys I am new to the page and would firstly like to introduce myself
my names josh and I've been messing with engines and stuff for quite a while now and have a pretty good base of mechanical knowledge.
But anyway I am building up a Path Winder kart I picked up for a couple hundred bucks after I went to this clandestine track and raced one of their "loaner" karts and I immediately fell in love with it. the place/karts are nothing fancy, a pretty crude sandy clay oval in the backyard of a greenhouse here in upstate NY. They run 5hp flat heads, but allow modifications to the engine EXCEPT the carb, which somewhat regulates everyone to stay competitive. The karts are One-Wheel-Drive, using the left wheel only, and they run the track COUNTER CLOCKWISE! gotta say it was tough getting used to turning the "wrong" way for the first few laps.
But to get to my point, I popped the side off the case last night on my Briggs I/C to remove my governor, and found a nice chunk of the end of the oil dipper sitting in the bottom of the case
. I can see some light scratches on the cylinder wall toward the very bottom, but the engine still runs great.
So my question is, do you think it would be alright to finish the season on this engine with just a new oil dipper installed? probably wont be more than 2 or 3 more races and I plan to do full teardown/build up of the internals this winter. If not, the kart has a 5hp Tecumseh endure OHV on it that runs well, but doesn't have much low end torque and once you run it in high rpms making a few passes, it seems like the needle valve can't full the bowl fast enough and she starves for fuel. let off it for a second to let the bowl fill, and it revs back up to normal.
Any tips on things I should do for the kart appreciated as well. Right now it's set up as a live rear axle, but the right rear is just on a bearing and free-spins. Most guys at the track just weld a 3/4x6 Grade 8 bolt on for their left rear axle and just run straight off that however I'd like to be able to switch back to 2wd in the off-season. MY kart is the green one, The black on is a kart that has run at the track for quite a while. I have a taller front left tire I just need to find some slick(ish) rears and she will be ready for race day
my names josh and I've been messing with engines and stuff for quite a while now and have a pretty good base of mechanical knowledge.But anyway I am building up a Path Winder kart I picked up for a couple hundred bucks after I went to this clandestine track and raced one of their "loaner" karts and I immediately fell in love with it. the place/karts are nothing fancy, a pretty crude sandy clay oval in the backyard of a greenhouse here in upstate NY. They run 5hp flat heads, but allow modifications to the engine EXCEPT the carb, which somewhat regulates everyone to stay competitive. The karts are One-Wheel-Drive, using the left wheel only, and they run the track COUNTER CLOCKWISE! gotta say it was tough getting used to turning the "wrong" way for the first few laps.
But to get to my point, I popped the side off the case last night on my Briggs I/C to remove my governor, and found a nice chunk of the end of the oil dipper sitting in the bottom of the case
. I can see some light scratches on the cylinder wall toward the very bottom, but the engine still runs great. So my question is, do you think it would be alright to finish the season on this engine with just a new oil dipper installed? probably wont be more than 2 or 3 more races and I plan to do full teardown/build up of the internals this winter. If not, the kart has a 5hp Tecumseh endure OHV on it that runs well, but doesn't have much low end torque and once you run it in high rpms making a few passes, it seems like the needle valve can't full the bowl fast enough and she starves for fuel. let off it for a second to let the bowl fill, and it revs back up to normal.
Any tips on things I should do for the kart appreciated as well. Right now it's set up as a live rear axle, but the right rear is just on a bearing and free-spins. Most guys at the track just weld a 3/4x6 Grade 8 bolt on for their left rear axle and just run straight off that however I'd like to be able to switch back to 2wd in the off-season. MY kart is the green one, The black on is a kart that has run at the track for quite a while. I have a taller front left tire I just need to find some slick(ish) rears and she will be ready for race day

kind of a "Loud" color but I like the brighter colors. Good news is the weather is gonna be crap all weekend so that should make waiting for my rod a little less annoying lol. Even the "s" word is in the forecast for tomorrow night :x