Only thing I'll add to this is the adapter he's using puts the carb at a 15° tilt. Maybe something or maybe nothing, but I do think the volume of fuel in the bowl is diminished.
Bob58o I wouldn't look into adjusting the float as much as I'd look into the flat mount kit from NR racing if you think fuel level is an issue.
http://www.nrracing.com/product-p/nr-cc390c.htm
Researching a thread, diff forum, similar build.
11-23-2013, 07:20 AM #50
vwfan79
"Everything looks good with your build but I have one question, and maybe its answered and I just missed it, your using a 390 carb with arc adapter is your motor plate on an angle? The reason I ask is that unless they have a new adapter the one I got is ment for kart racing where the motor is at 15 degrees. On a flat surface it drowns the idle circuit and the motor doesn't want to idle good if at all. On a flat surface my motor will only idle on half choke, but once I get going it screams with the 390 carb. I have a similar build as you and will be seen in a future bike build, my specs are hemi block .010 head gasket Honda 14cc head all port matched ss valves with locks and retainers 26# springs 1.3 rockers black mamba cam arc rod 390 carb with air filter rlv header, I feel like I might have missed something but you get the idea. Anyways great thread love all the detail."
---------- Post added at 02:41 AM ---------- Previous post was at 02:25 AM ----------
http://www.nrracing.com/product-p/nr-cc390b.htm
This is the two piece carb adapter that NR sells.
Designed to mount GX390 Type Carbs to GX200, 6.5s, and 212 Predators.
2 pc Design can be used on both flat and 15 degree mounts.
Typically requires a 108 Main Jet for std bore Gas GX390 carbs and 110 for Gas Bored Carbs. Methanol carbs will need a 150 to 160 Main or larger.
Pulse Fitting can be installed for operating fuel pumps, otherwise plug can be used to seal opening. NOTE: PULSE FITTING FACES UP Note: On some Long Duration (radical) cams, the intake vacuum signal is too weak to operate the fuel pump, esp when using methanol. In this case, you will need to pulse from the valve cover or block.
Instructions: Mount the 15 degree adapter (the thicker one) to Engine. Mount Flat Plate adapter to the 15 degree adapter. Use a small amount of gasket sealer between the two. Install the carb studs in appropriate holes, mount carb using enclosed gasket, and go racing.
---------- Post added at 02:44 AM ---------- Previous post was at 02:41 AM ----------
Long style gx390 to 200 manifold
http://www.nrracing.com/product-p/qmnrr-12.htm
Intake Manifold, GX390 Carb to GX200. Does not require insulator plate. Includes Pulse fitting for Fuel pump.
Typically requires a 100 Main Jet for std bore Gas GX390 carbs and 102 or 105 for Gas Bored Carbs. Methanol carbs will need a 150 to 160 Main
---------- Post added at 02:51 AM ---------- Previous post was at 02:44 AM ----------
"I talked to russ about the safe issue regarding the arc adapter. i told him the air bleed on the back of the 390 carb was un able to vent with just the adapter.... you can do two things... One is run a insulator...and you still at a 15 deg angle, or you can jb weld the back of the carb, and drill the air bleed on top/side of carb with a small nipple to vent...this will allow no insulator just gaskets and give the true stock appearing look. If you get nr racings 390 to gx200 adaptor it all ready had the insulators vent areas built in...and will sit at the angle you need... if you go this route the carb is nowhere near as aggressive as the short arc adapter..it feel like a 22mm at best... the first way at the 15 angle did idle and surge...but as soon as you got full throttle it was like warp speed...just food for thought."