22 MM Mikuni Carb Advice needed bad

Status
Not open for further replies.

justinkk2005

New member
Messages
56
Reaction score
0
My setup:
Gx200 clone
flat top piston
billet rod
no govenor
18 lbs valve springs
mikuni 22mm carb


Carb setup:
Needle on 4th position
120 Main Jet
stock air screw and pilot jet

The problem i'm having is really getting to me. At full throttle (after you get it going, not at takeoff) it runs and pulls amazing so that has to limit the main jet from being the problem. When I pull out I have to give it half throttle just to keep it running right or it dies. It doesnt want to idle unless u setup the idoling REALLY high and then if you give it gas and let off it wont idle and it dies. I set the needle on the 5th position and it black smoked so bad it was crazy so I put it on the 3rd and then it would'nt hardly run at all and its now back on the 4th. Any advice?
 

Kaptain Krunch

Pro Junk Collector
Messages
4,636
Reaction score
6
Location
vermont
the needle mainly affects mid range, not idle. do a plug chop and adjust the air screw/change out pilot jets if needed. When you say 3rd 4th 5th etc, do you mean 3rd from the bottom of the needle or the top? remember the higher the clip is up on the needle, the leaner the mid range mixture.
 

justinkk2005

New member
Messages
56
Reaction score
0
It does awesome with the clip set on the 4th position (toward the bottom, which is richer I know)

I put it on the 5th and it was rolling black smoke and at idle it runs like crap. Like if i'm sitting still and put it to the floor it dies, you have to hold it half throttle, get it going and then open it up. It sucks because I do alot of dead stop and go dragging with friends
 

justinkk2005

New member
Messages
56
Reaction score
0
rich idle circuit maybe? try turning the air screw out in say 1/4 turn increments and testing it.

I will sir thank you! I mean partial throttle, tip-in, and full throttle it pulls like crazy but at very low end (air screw/pilot jet areas) it's horrible. those pilot jets are $8 a piece, I really cant afford to buy one and it be too lean or too rich. Idk which way to go, up or down if the air screw dont work. When it idles its like a rough idle I mean like its cammed to death or something.
 

NapO

New member
Messages
136
Reaction score
0
Location
Canada
the pilot jet maybe the way to go. agk.com tested a mikuni and found the best set up was 125 or 130 main jet and 12.5 pilot for them. i used one of their jets they recommended on my honda carb and the fuel mixture was perfect.
 

jr dragster T

New member
Messages
3,966
Reaction score
10
Location
Cold place
When I had a 15 pilot jet in my Mikuni 22 on my modified GX200 it would idle pretty lopey and sputter/blow black smoke when trying to accelerate. Try opening up the air bleed and if this fixes it, Your probably too rich on the bottom. I would purchase a 12.5 pilot as thats what seems to work best for most with some air bleed tuning.
 

EagleTalons

Master JB Welder
Messages
1,100
Reaction score
5
Location
Forsyth, Montana
I will sir thank you! I mean partial throttle, tip-in, and full throttle it pulls like crazy but at very low end (air screw/pilot jet areas) it's horrible. those pilot jets are $8 a piece, I really cant afford to buy one and it be too lean or too rich. Idk which way to go, up or down if the air screw dont work. When it idles its like a rough idle I mean like its cammed to death or something.

MFG sells pilots for $2 each.
 
Status
Not open for further replies.
Top