Search results

4.10/3.50-5 and Im using this setup http://www.bmikarts.com/item/4.10-3.50-5-Complete-Assembly-Tire-Rim-Sprocket-Brake---260090-6264

I made a mistake my clutch has 12 teeth will this make a difference ?

sprockets lined up.

3/4" Bore with 3/16" Keyway #41, 54T Sprocket I have not had any time or rather its been too hot outside... so I finally got around to mounting the new motor and put on the clutch. Went out and bought some washers so that the wheel sprocket now lines up with the clutch sprocket. I took an old...

Per your picture its the electronic ignition coil: (solid state) I assume that these are cheap and easy to replace ... I assume I should pull the one off the engine to find a parts number to order a new one ? Or do I need to find a part number off the engine ?

Im new to this so I dont really know how to tell. How do I tell the difference ?

Just took it off the tiller and will be mounting it on the kart in a few days. And then it will be time to find a chain. Thanks

Where can I get the linkage/cables etc ... new to carts and my Carts are missing linkage so I will have to come up with something on my own, plus have an engine that I may be pulling off a garden tiller. I will post a picture of the current throttle setup tommorow . Thanks in advance.

Also ... ask the owner of the property if you can use the parking lot after the businesses close. If he/she says yes then ask them to put it into writing along with there contact info so if the cops do show up you can tell/show them that you have permission.

The parking lot will more then likely be considered private property but the problem will be that one of the businesses, who the parking lot belongs to may have a complaint. So dont be surprised if one of the businesses that neighbor the parking lot or its customers call the police after seeing...

Sorry im new to this Now how to I determine how long a chain I need. my clutch has 10 teeth on it. This is the info from the sprocket... 3/4" Bore with 3/16" Keyway #41, 54T Sprocket 4" Brake Drum Thanks and yes i am a noob.

Now I have received this and everything appears to line up pretty close except I will need to put 2-3 big washers on before the wheel so that it lines up with the clutch. Now how to I determine how long a chain I need. This is the info from the sprocket... my clutch has 10 teeth on it. 3/4"...

Thanks I just ordered...

I recently picked up a cart and its missing the drive sprocket and wheel mount. I was looking around on ebay and found this and I believe this is exactly what I need for $72. Can anyone recommend another site to get this setup any cheaper ?

I completely took the wires out and it still wont crank.

I plan to take the motor off and make sure that it is flat as at a glance it appears there may be something under the engine that may have it leaning slightly. Also where can I find a wheel with a mounting plate on it ? As in looking at the drive side wheel on this cart its missing the plate...

I grabbed the top of the spark plug at the same time as I pulled the cord and it does not shock me. If the coil was working shouldnt it shock the crap out of me if I am holding it (top of spark plug) at the same as I pull the cord ?

Pull string broke a few days ago and while I was replacing it I decided that I would trying to setup a kill switch since in a few days I plan to carry it to a shop to get scrub pads welded on it. This is a brigs and straton engine. Normally the engine will crank after 2 or 3 pulls and me...

The fun part is going to be in getting the correct sprocket and fitting everything together. In looking at how everything currently sits everything needs to shift over about an inch.

Went to pay the guy today for the cart ... (he was storing it at neighbors house) and he gives me a clutch . Its says max-torque and it has the number 8 on the back. So how do I determine what sprocket for the wheel do I need ?